Mitsumi electronic WD-73734 Flat Panel Television User Manual


  Open as PDF
of 84
 
4. TV Operation and Features 27
Note: Tooperateotheraudio/videodevices:
• SeeAppendixD,“ProgrammingtheRemote
Control.”
• Seechapter6,“NetCommand,”forNetCommand
IR“Learning”ofdevicekeys.
• ForHDMIdevicescompatiblewiththeTV’s
NetCommandforHDMIfeature,seebelow.
ChannelView™ Channel Listings
ChannelViewshowsmemorizedchannelson
ANT 1
and
ANT 2
.Itdisplayschannelnamesandprogram
informationassentbybroadcastersoryourlocalcable
serviceproviderandmaybeincomplete
.
Noprogram
informationisdisplayedforanalogchannels.Ananalog
channelnameisdisplayedonlyifyouassignedaname
intheSetup > Editmenu.
T
oreceiveChannelViewupdates,settheEnergyMode
toFast Power OnandleavetheTVpoweredofffora
whileeachday.
Using ChannelView
Feature Press Key
SeeChannelViewlistings
fromANT 1orANT 2.
Press
GUIDE.
CloseChannelView Press
GUIDE
or
EXIT.
Scanchannelsonebyone.
Pressandhold
or .
Scanchannelsquickly.
Pressandhold
PAGE
/
.
Jumptolistingsforaspe-
cificchannel.
1. Enterthechannel
number(seenumbers
inupperleft.
2. Press
ENTER
.
Seemoreoftheprogram
description.
Press
INFO
.
Movenavigationtothe
programguide.
Press
.
Movenavigationtothe
channelguide.
Press
.
Tunetothehighlighted
channel.
Press
ENTER
.
Record/Playback Keys
Useanyofthesemethodstoenabletherecordingand
playbackcommands:
• ProgramtheremotecontrolforyourDVR,VCR,or
DVDplayer/recorderandsettheslideswitchto
VCR
,
DVD
,
CABLE
,or
SAT
.
• Yand734seriesTVs:PerformNetCommandIR
“learning”forthedevice.
• CheckHDMIdevicesforcompatibilitywiththeTV’s
NetCommandforHDMIfeature(seebelow).
23. (
PAUSE
): PausesaVCR,DVR,orDVD.See
aboveforuseduringTVviewing.
24.
(
PLAY
):PlaysaVCR, DVR, orDVD.
25.
(
RECORD
):
RecordswithaVCRorDVR.
26. (
STOP
):StopsplayofaVCR, DVR, orDVD.
27.
(
REVERSE
): RewindsaVCR.Reversescansa
DVRorDVD.
28.
(
FORWARD
):FastforwardsaVCR.Forwardscans
aDVRorDVD.
Remote Control, continued
Care of the Remote Control
• Useonlyalkalinebatteries.
• Bewithin20feetoftheequipment.
• Donotpresstwoormorebuttonsatthesametime
unlessinstructedtodoso.
• Donotallowunittogetwetorbecomeheated.
• Avoiddroppingonhardsurfaces.
• Donotuseharshchemicalstoclean.Useonlya
soft,lightlymoistenedcloth.
• Donotmixoldandnewbatteries.
Resetting the Remote Control
Iftheslideswitchissetto
TV
andtheTVdoesnot
respondproperly,resettheremotecontrol.
1. Pressandhold
POWER
forseveralsecondsuntilthe
buttonblinkstwiceandgoesoff.
2. Releasethe
POWER
button.
3. Presskeys
0 0 9 3 5
andthe
POWER
buttonwillblink
twicewhenyoufinishenteringthecode.While
enteringthecode,pauseforamomentbetween
eachkeypresstoensureitisrecognized.
Low-Battery Indicator
Ifyoupressakeyandthe
POWER
keyblinksfivetimes,
replacetheremotecontrol’sbatteries.
NetCommand for HDMI Devices
TheTV’sremotemayoperatesomefunctionsof
compatibleHDMIdevicesabletoreceivecommands
throughtheHDMIcable.Testyourequipmentwiththe
TV’sremotetofindoutwhichcommandsaresup-
ported.Seebelowforcommandsthatmaybeavail-
able,dependingontheindividualdevice.
Press
PLAY
onthedeviceitselfto:
• TurnontheTVifnotalreadyon
• Switchtothedevice(noneedtodisplaytheInput
Selectionmenu)
• Beginplayofthedevice
VCR,DVD,andDVRfunctionsthatmaybeavailable:
Record/
Playback
Menu
Navigation
Channel Tuning Other
CH
/
GUIDE
ENTER
Digits
0–9
,
—
CANCEL
F1
(content)
—
CANCEL
(tocancel)
ENTER MENU
 previous next