Mitsumi electronic WD-73734 Flat Panel Television User Manual


  Open as PDF
of 84
 
6. NetCommand 49
Initial NetCommand Setup for Most
Devices
Toperformthisprocedure,youneed:
• TheremotecontrolsforboththeTVandthe
deviceyouwanttocontrol.
• TheIRemittercablesuppliedwiththeTV.
Note: TosetupanA/Vreceiver,see“SetUp
NetCommandControlofanA/VReceiver”later
inthischapter.
1. ConnectandpositiontheIRemittersforthe
devicesyouwishtocontrol.See“IREmitterPlace-
ment”inthischapter.
2. SettheTV’sremotecontrolslideswitchtothe
TV
position.
3. OpentheNetCommandLearnscreeninoneoftwo
ways:
• IfworkingfromtheAuto Input Sensingscreen
forthedevice,highlighttheLearniconand
press
ENTER
toopentheLearnscreenforthe
device.
• IfperformingNetCommandsetupatanytime
afterthedevicehasbeenrecognizedthrough
AutoInputSensing:
a. Press
INPUT
toopentheInput Selection
menu.
b. Highlightthedesiredinputiconandpress
ENTER
toswitchtothatinput.
c. Press
MENU
,highlightInputs,andhighlight
LearntoopentheLearnscreenforthe
device.
4. ThefirstfunctionhighlightedintheLearnscreen
isalwaysPower On.AimtheTV’sremotecontrol
attheTVandpress
ENTER
tobeginlearningforthat
function.
5. WhenthePower Ontextstartsflashing,aimthe
device’sremotecontrolattheTVandpressand
holdthe
POWER
keyuntilacheckmarkappearsnext
toPower On.
• Ifthetextstopsflashingbeforethecheckmark
appears,repeatthisstep.
• ToremovethekeyfromNetCommandcontrol,
pressthe
CANCEL
keywhilethekeynameis
highlighted.
6. Pressthe keysontheTV’sremotecontrol
tohighlightotherkeysonthelist.Repeatsteps
4and5foreachadditionalfunctionyouwishto
controlthroughNetCommand.
7. Ifthedevice’sremotecontrolhaskeysthatarenot
inthelist,youcanassociateuptoanyfourkeys
withthe
F1
through
F4
keys.
Forexample,foraDVDplayer,assignthe
F1
and
F2
keystotheDVDplayer’s
CHAPTER SKIP FORWARD
and
CHAPTER SKIP BACK
keys.PerformNetCommandsetup
forthe
F
keysthesameasyoudidforthenamed
keys
.
8. Ifthedevicehasaseparate
POWER OFF
key,press
ontheTV’sremotetohighlightPower Off.
Repeattheearlierstepsto“learn”the
POWER OFF
key.
If the device has no
POWER OFF
key, skip this step.
9.
Press
EXIT
tofinishNetCommand“learning”forthe
currentdevice.
From the Auto Input Sensing screen, highlight the Learn
icon and press ENTER to open the NetCommand Learn
screen.
Inputs > Learn screen
Add or Remove Device Keys from
NetCommand Control
1. Press
INPUT
toopentheInput Selectionmenuand
selecttheaffecteddevice.
2.
OpentheInputsmenuandhighlighttheLearnicon.
3. WhentheLearnscreendisplays:
• Toaddkeys:Continueasdescribedearlier
under“InitialNetCommandSetupforMost
DeviceTypes.”
• Todeletekeys:Highlightthenameofthekey
youwishtodeleteandpress
CANCEL
ontheTV‘s
remotecontroltoclearthecheckmark.
 previous next