Mitsumi electronic WD-73734 Flat Panel Television User Manual


  Open as PDF
of 84
 
64 Appendices
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Programming the Remote Control
1. Movetheslideswitchatthetopoftheremotetothe
positionfortheproductyouwanttocontrol.Refer
tothetablebelow.Onlyoneofeachdevicetype
canbecontrolledineachslide-switchposition.
Switch Position Affected Device
CABLE/SAT
CableBox
DTVReceiver
SatelliteReceiver
VCR
VCR
DVR
LaserDiscPlayer
DVDPlayer/Recorder
DVD
DVDPlayer/Recorder
DVR
LaserDiscPlayer
VCR
AUDIO
A/VReceiver
AudioAmplifier
CDPlayer
2. Pressandhold
POWER
ontheremotecontrolfor
severalsecondsuntilthebuttonblinkstwiceand
goesoff.
3. Releasethe
POWER
button.
4. Enterthefirstfive-digitcodelistedforyourequip-
ment.
• The
POWER
buttonblinkstwicewhenyoustartto
enterthecodeandthenonceforeachaddi-
tionalkeypress.
• The
POWER
buttonblinkstwicewhenyoufinish
enteringavalidcode.
• Movetheslideswitchtoanotherpositionifyou
needtostartoverorwishtoexitprogramming
mode.
5. Pointtheremotecontrolattheequipmentand
press
POWER
.Iftheproducthasnopoweron/off
function,pressadifferentkey,suchas (
PLAY
),
(
STOP
),
VOL
,or
MUTE.
• Iftheequipmentresponds,theremotecontrol
isproperlyprogrammedtooperatetheequip-
ment.
• Iftheequipmentdoesnotrespond,repeat
steps2–4withthenextfive-digitcodelistedfor
yourequipment.
6. Onceyouhavefoundthecorrectcode,writeitin
thespacebelowforfuturereference.
Switch Position
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
Code Verification
Todeterminethecodeprogrammedforanypositionof
theslideswitch:
1. Movetheslideswitchtothepositionyouwishto
verify.
2. Pressandhold
POWER
ontheremotecontrolfor
severalsecondsuntilthebuttonblinkstwiceand
goesoff.
3. Presskeys
9 9 0
4. Press
1
andcounttheblinksofthepowerbutton.
Writedownthenumberofblinksasthefirstdigitof
thecode.
5. Repeatstep4forthesecond,third,fourth,andfifth
digitsofthecode.
Appendix D: Programming the Remote Control, continued
Audio Lock: Universal A/V Receiver Control
WithAudioLockactive,theremotecontroloperates
thevolumeandmutefunctionsoftheA/Vreceiverinall
positionsoftheslideswitch.ActivateAudioLockifyou
normallyuseanA/VreceiverwithyourTVandother
A/Vequipment.
1. Programthe
AUDIO
positionforyourA/Vreceiveras
describedearlierinthissection.
2. Movetheslideswitchtothe
AUDIO
position.
3. Pressandhold
POWER
ontheremotecontrolfor
severalsecondsuntilthebuttonblinkstwiceand
goesoff.
4. Presskeys
9 9 3 ENTER
The
POWER
buttonwillblinktwicetoindicateAudio
Lockisactive.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
1. Pressandhold
POWER
forseveralsecondsuntilthe
buttonblinkstwiceandgoesoff.
2. Presskeys
9 9 3 VOL
.
The
POWER
buttonwillblinkfourtimestoindicate
AudioLockhascleared.
 previous next