Onkyo DR-2000 DVD Player User Manual


 
8
Preparing the Remote Controller
Inserting the Batteries
1 Detach the battery cover.
2 Insert the two size AA/R6/UM3 batteries.
Be sure to match the + and ends of the batteries with
the diagram inside the battery compartment.
3 Attach the battery cover.
Using the Remote Controller
Switching the remote controller function
modes
Some buttons on the remote controller have two or
more functions. To set the functionality of these buttons,
press one of the four MODE (AUDIO, DVD, TA/MD, TV)
buttons in advance.
The function mode remains the same until another
MODE button is pressed.
(Details about the functions and the related function
modes are explained in each section.)
Notes
When the batteries are getting weak, the SEND/
LEARN indicator on the remote controller starts
flashing. In this case, replace the batteries with
new ones.
For the other functions of this indicator, see
Pointing the remote controller in the right
direction on the right, and page 63.
Do not mix new batteries with old batteries or
different kinds of batteries.
To avoid corrosion, remove the batteries if the
remote controller is not to be used for a long time.
Remove dead batteries immediately to avoid damage from
corrosion. If the remote controller does not operate smoothly,
replace both batteries at the same time.
The life of the supplied batteries is about six months but this varies
depending on usage.
Pointing the remote controller in the right
direction
Point the remote controller toward the remote control
sensor.
Press MODE AUDIO first before operating the speaker
setting and sound related operations.
Press MODE TA/MD first before operating the Onkyo
MD recorder or z-connected cassette tape deck (see
pages 12 and 31).
Press MODE TV first before operating your TV.
To operate the TV with the supplied remote controller,
you need to let the remote controller learn the TV
remote control signals (see pages 31 and 63).
12
3
SEND/LEARN
indicator
This indicator is
lit while any
button on the
remote controller
is pressed.
30˚
30˚
About 5 m (16 feet)
Remote control sensor
SEND/LEARN
indicator
I
N
P
U
T
S
E
L
E
C
T
O
R
M
O
D
E
A
U
D
I
O
D
V
D
T
V
T
A
/
M
D
L
I
S
T
E
N
I
N
G
M
O
D
E
A
.
C
T
R
L
T
D
S
T
E
R
E
O
S
U
R
R
T
I
T
L
E
M
E
N
U
S
E
T
U
P
T
V
/
V
C
R
R
E
T
U
R
N
CH
TUN
VOLENTER
REPEAT MUTING
A B
REC
DIMMER
OPEN/CLOSE
RANDOM SLOW
SUBTITLE ON / OFF
ANGLE ZOOM
S
T
N
B
Y
O
N
S
L
E
E
P
M
O
D
E
A
U
D
I
O
D
V
D
T
V
T
A
/
M
D
M
O
D
E
A
U
D
I
O
D
V
D
T
V
T
A
/
M
D
MODE buttons
Press MODE DVD first before operating
the built-in DVD player.
M
O
D
E
A
U
D
I
O
D
V
D
T
V
T
A
/
M
D
I
N
P
U
T
S
E
L
E
C
T
O
R
M
O
D
E
A
U
D
I
O
D
V
D
T
V
T
A
/
M
D
L
I
S
T
E
N
I
N
G
M
O
D
E
A
.
C
T
R
L
T
D
S
T
E
R
E
O
S
U
R
R
T
I
T
L
E
M
E
N
U
S
T
N
B
Y
O
N
S
L
E
E
P
S
E
N
D
L
E
A
R
N
I
N
P
U
T
S
E
L
E
C
T
O
R
M
O
D
E
D
V
D
T
A
/
M
D
S
T
N
B
Y
O
N
S
L
E
E
P
S
E
N
D
L
E
A
R
N
Notes
Place the unit away from strong light such as direct sunlight or
inverted fluorescent light which can prevent proper operation of the
remote controller.
Using another remote controller of the same type in the same room
or using the unit near equipment which uses infrared rays may
cause operational interference.
Do not put any object (such as a book) on the remote controller. The
buttons of the remote controller may be pressed by mistake and
drain the batteries.
Make sure the audio rack doors do not have colored glass. Placing
the unit behind such doors may prevent proper remote controller
operation.
If there is any obstacle between the remote controller and the
remote control sensor, the remote controller will not operate.