Panasonic AJ-D92P VCR User Manual


 
46
100 SEARCH SPEED
0000
0001
X4.1
X8.4
For setting the speed at which the tape is to be decelerated when the
search switch on the front panel has been pressed.
0: 4.1
a
normal tape speed
1: 8.4
a
normal tape speed
101 SHTL MAX
0000
0001
0002
X8.4
X16
X32
For setting the maximum speed in the shuttle mode when the external
controller connected to the 9-pin remote connector is used.
0: 8.4
a
normal tape speed
1: 16
a
normal tape speed
2: 32
a
normal tape speed
105 STOP MODE
0000
0001
REC
PB
For setting the mode of the digital circuit in the stop mode.
0: The digital circuit serves as the REC circuit. It takes a shorter time for
operation to transfer to the REC mode.
At this point, the E-E mode is established.
1: The digital circuit serves as the PB circuit. It takes a shorter time for
operation to transfer to the playback mode.
106 HUMID OPE
0000
0001
OFF
ON
For setting whether to ignore condensation when it has formed and
continue with operation.
0: Unit does not continue to operate when condensation has formed.
1: Unit continues to operate when condensation has formed, in which case
it cannot be guaranteed that the unit will operate normally.
<Note>
Since the tape may be damaged with a “1” setting, this item should normally
be set to 0 (no operation).
107 WIDE MODE
0000
0001
WIDE
NORMAL
For setting whether to perform recording in the wide mode.
0: Recording is performed in the wide mode.
1: Recording is performed in the 4:3 normal mode.
102 FF. REW MAX
0000
0001
0002
X16
X32
X60
For setting the maximum fast forward and rewind speed.
1: 16
a
normal tape speed
2: 32
a
normal tape speed
3: 60
a
normal tape speed
<Note>
When the 50 Mbps mode has been selected as the menu item No. 007
(SYS FORMAT) setting, the tape will run at 32
a
the normal tape speed
even if 60
a
has been selected.
OPERATION menu
Item Setting
No.
Superimposed
display
No.
Superimposed
display
Description of setting
The underlining indicates the factory setting.
Setup Menus
111 AFTER CUE-UP
0000
0001
STOP
STILL
For setting the status after cue-up.
0: For stopping the tape in the stop mode.
1: For stopping the tape in the still mode.
110 AUTO BACK
0000
0001
0002
OFF
REC-P
ALL
For setting the operation method of the frame-to-frame continuity function
(for setting the operation of the auto back function for rewinding the tape for
several seconds in order to eliminate disturbances in the recorded pictures).
0: Auto back function is disabled (no continuity between frames).
1: In the REC PAUSE mode, the auto back function is activated to ensure
frame-to-frame continuity.
2: Regardless of the VTR mode, the auto back function is activated to
ensure frame-to-frame continuity.
113 BATTERY SEL
0000
0001
0002
0003
0004
BP402
BPH90
BPH100
HP90
HP90A
For setting the type of battery.
0: AU-BP402 (made by Matsushita Electric Industrial), 12 V nickel-cadmium
battery
1: BP-H90 (made by IDX), 12 V nickel-hydrogen battery
2: BP-H10C (made by IDX), 13 V nickel-hydrogen battery
3: HP-H90 (made by PACO), 13 V nickel-hydrogen battery
4: HP-H90A (made by PACO), 13 V nickel-hydrogen battery