Filter
Top Products
Reference
66
VQT0N92
On the unit’s display Page
On the TV Page
On the unit’s display Page
On the TV Page
Error messages
∫ Common
H, F
(“” stands for a number.)
≥An error has occurred. The number following “H” or “F” depends on the status of the unit. Check
the items in the “Error messages” section and the “Troubleshooting guide”. If the service number
still does not disappear after the check, follow the Reset procedure described below.
Reset procedure: (“The unit is on but cannot be operated.” l 68)
≥
If the service numbers fail to clear, note the service numbers and contact a qualified service person.
–
–
∫ DVD
Cannot finish recording
completely.
≥The program was copy-protected.
≥The disc may be full.
≥There are already 99 recorded titles ([+R] 49 recorded titles).
–
–
–
Cannot play. ≥You inserted an incompatible disc (Discs recorded in PAL video, etc.). –
Cannot record on the disc. ≥The disc may be dirty or scratched. 8
Unable to format.
Please check the disc.
Cannot record. Disc is full. ≥Create space by erasing any unwanted titles. [RAM] [-RW‹V›]
[Even if you erase recorded content from the DVD-R or +R, there is no increase in disc space. Available
disc space on DVD-RW (DVD-Video format) increases only when the last recorded title is erased.]
≥Use a new disc.
22, 30,
33
–
Cannot record. The number
of titles has exceeded the
maximum limit.
Error has occurred. Please
press ENTER.
≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering
(“SLF CHECK” appears on the unit’s display).
–
No disc ≥You haven’t inserted a disc. Correctly insert a disc that the unit can play.
≥The disc is upside down. If it is a single-sided disc, insert it so the label is facing up.
6, 8
8
Please change the disc. ≥There may be a problem with the disc. Press [<, OPEN/CLOSE] to remove it and check it for
scratches or dirt. (The unit turns off automatically after you open the tray.)
8
This is a non-recordable disc. ≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R, DVD-
RW (DVD-Video format) or +R.
≥You inserted an unformatted DVD-RAM or DVD-RW. Format the disc with the unit.
–
31
This disc is not formatted
properly.
≥The operation is prohibited by the unit or disc. 21
CHK REMOTE
(“” stands for a number.)
≥The remote control and main unit are using different codes. Change the code on the remote
control.
19
HARD ERR ≥
If there is no change after turning the unit on and off, consult the dealer where the unit was purchased.
–
NO READ ≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥You have used a lens cleaner and it has finished. Press [<, OPEN/CLOSE] to eject the disc.
8
8
PLEASE WAIT ≥Displayed when the unit is started. This is not a malfunction.
≥The unit is carrying out its recovery process. You cannot operate the unit while “PLEASE WAIT”
is displayed.
–
–
PROG FULL ≥
There are already 16 scheduled recording programs. Delete unnecessary scheduled recording programs.
29, 53
SLF CHECK ≥There was a power failure or the AC plug was disconnected while the unit was on. The unit is
carrying out its recovery process. Wait until the message disappears.
≥If “Quick Start” is set to “On”, “PLEASE WAIT” is displayed while the unit is carrying out its
recovery process. You cannot operate the unit while this is displayed.
–
–
UNSUPPORT ≥You have inserted a disc the unit cannot play or record on. 7
UNFORMAT ≥You have inserted an unformatted DVD-RAM or DVD-RW that is unformatted or recorded on
other equipment.
31
U59 ≥The unit is very warm.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan on the
rear of the unit.
–
U99 ≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to
standby. Now press [POWER Í/I] on the main unit again to turn the unit on.
–
∫ VHS
PLEASE PUT IN A VIDEO
CASSETTE.
≥A video cassette is not inserted when recording programs or setting the scheduled recording.
Insert a video cassette with an accidental erasure prevention tab.
48
PLEASE SET THE CLOCK. ≥The clock is not set when recording programs or setting the scheduled recording. Set the clock. 46
PLEASE USE A CASSETTE
WITH TAB.
≥
A video cassette without the accidental erasure prevention tab is inserted when recording programs or
setting the scheduled recording. Use a video cassette with an accidental erasure prevention tab.
48
VHSDVD
ES30VP&PC.book 66 ページ ２００５年２月２１日 月曜日 午後２時３２分