Filter
Top Products
Getting Started
11
Tuning the TV to Your Unit
The unit supplies a signal to the TV via the RF coaxial cable on channel AU28s 69 or NZ21s 69. It is possible to view the unit’s picture on
your TV in the same way that you watch TV broadcasts. The unit is fitted with its own tuner (just like a normal TV) and can be preset to receive
up to 99 TV broadcast stations.
≥Press [VHS].
¬ If you have connected the unit to the TV through the audio/video output sockets
You do not need to follow the procedure below. To view the pictures from the unit, set to the AV mode on the TV with [AV].
The local TV broadcast channels 2, 7, 9, 10 and 28 are factory-preset in the unit.
That is, if you can receive TV broadcasts on VHF channels 2, 7, 9, 10 and UHF channel 28, these are
already tuned on the programme positions with the matching numbers.
[1] Press [VHSÍ] to turn on this unit.
[2] Hold down [MENU] for 5 seconds or more.
[3] Set the TV to an unused position for the unit
viewing channel.
≥Tune the TV until the display shown on the right appears. Refer also to
the TV’s instructions regarding tuning.
[4] Press [MENU].
When the unit is turned on after connecting the aerial cable and the
mains lead for the first time, tuning starts automatically.
≥If the unit is turned on with the aerial not connected, all channels are skipped.
[1] Press [VHSÍ] to turn on this unit.
[2] Set the TV to an unused position for the unit
viewing channel.
≥Tune the TV until the display shown on the right appears. Refer also to
the TV’s instructions regarding tuning.
[3] Press [MENU].
¬ To cancel Auto Tuning partway through
Press [MENU]. Auto Tuning will stop halfway by turning the unit off, pressing [MENU], playback or a
power failure.
¬ If Auto Tuning stops halfway by turning the unit off, playback or a power failure
≥Disconnect the mains lead and then reconnect it.
≥Turn on the unit. Plug in Auto Tuning restarts.
¬ To set the channels manually (l 23)
ªTo restart Plug in Auto Tuning
≥Turn the unit on.
≥Make sure there is no video cassette in the unit.
1) Keep both [CH] J and I on the unit
pressed simultaneously for 3
seconds or more until the channel on the unit’s display changes to 1.
2) Disconnect the mains lead and then reconnect it.
3) Turn on the unit. Plug in Auto Tuning restarts.
You can change the RF output channel, for example, when interference
occurs on the picture after tuning.
................................................................................................................................................................................................................
1) Hold down [MENU] for 5 seconds or more.
2) Press [CH]JI to select the channel (AU28s69, NZ21s69).
≥Each time you press [CH]JI (l left)
≥Set to “ss” (RF OFF) when you use the audio/video cable for the
connection.
≥You can also use the numeric buttons.
Example: “28”; [2]l[8]
3) Retune your TV to the new RF channel for the unit.
4) Press [MENU] to exit the setting mode.
Note:
≥Even if the RF output channel has been changed, it is not necessary to
perform Auto Tuning.
SLOW/
SEARCH
REW
FF
VHS/DVD
VHS
INDEX/SKIP
PLAY
TRACKING/V-LOCK
JET REW
CH
AV
VOLUME
DVD
PLAY LISTDIRECT NAVIGATOR
TOP MENU
RETURN
DISPLAY
PLAY MODE
REC MODE
VHS/DVD
CANCEL/RESET
QUICK REPLAY
AUDIO
REC
ENTER
PLAY SPEED
P.MEMORY
SLOW
-/-
-
MENU
AV ENHANCER
PROG/CHECK
SET UP
I-TIMER
TIMER
DVD-RAM
DUBBING
PROG PLAY
INPUT SELECT VHS STATUS
DVD STATUSPICTURE MODEGROUP
NAVI
MENU
VHS
CH
AV
VHS
/ I
EJECT
FULL-OPEN
PLAY
STOP
CH
REC/OTR
LR
j
AUDIO
j
VIDEO
AV2 IN
CH
Numeric
buttons
Pre-programmed TV Channels (for NV-VP32GL/Australia)
Plug in Auto Tuning (for NV-VP32GN/New Zealand)
To change the RF output channel
Panasonic
END: MENU
CH 22 SEARCH
END: MENU
21
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
END: MENU
AUTO TUNING IS
COMPLETED.
Disappears 1
Panasonic
END: MENU
NV-VP32GL
NV-VP32GN
28
…
69
(RF OFF)
NV-VP32GL
21
69
(RF OFF)
NV-VP32GN
VP32GL.book 11 ページ ２００４年６月１１日 金曜日 午後４時３２分