Filter
Top Products
English
You cannot insert a video cassette.
•
Insert the tape, window side up, with the record tab facing you.
•
Make sure a tape isn’t already in the VCR by pressing STOP/EJECT C A on the front of the DVD/VCR.
•
Gently push on the center of the tape when putting it in the VCR. Never force the tape into the VCR.
•
If a timer recording is set, you cannot insert a tape without a record tab.
You cannot remove the tape.
•
Make sure the power plug is completely connected to a power outlet.
•
If a timer recording has been set, press TIMER SET on the remote control or STOP/EJECT C A on the front panel to
cancel the timer standby mode temporarily.“ ” will disappear from the display panel.Then, press STOP/EJECT C A
on the front of the DVD/VCR to eject the tape. Insert another tape and press TIMER SET to reset the timer
recording.
• Unplug the DVD/VCR power cord for 5 minutes.Then, plug in the power cord again and pressy on the
DVD/VCR. Press STOP/EJECT C A on the DVD/VCR 3 to 5 times. If the tape still does not eject, you
may need to have an authorized servicer remove the tape.
DVD/VCR ejects the tape when you press REC I or TIMER SET.
•
Make sure the tape has a record tab. Details are on page 24.
Satellite Receiver Hookups
•
Watching one TV channel while recording another may not be possible if you have a Satellite Receiver. Set your TV to
channel 03 or 04, then make your channel selections at the Satellite Receiver.
•
With many Satellite Receiver hookups, if you use audio and video cables to connect your DVD/VCR to your TV,you
will have to put your DVD/VCR in line input mode (L1 or L2).
Line input mode
•
If you accidentally enter line input mode (L1 or L2 will appear on your TV screen briefly), press CH + or CH - or the
Number buttons to select another channel.
Hi-Fi Stereo Sound
•
During playback, Hi-Fi audio may normally revert to normal audio when you adjust tracking.
•
When connecting the DVD/VCR to a TV with the red and white audio cable, you will only get stereo sound if you
connect the DVD/VCR AUDIO OUT jacks on the DVD/VCR to the AUDIO IN jacks on your TV, and if the TV is on
its Audio/Video In channel. See your TV owner’s manual for details.
•
When you connect the DVD/VCR AUDIO OUT jacks on the DVD/VCR to the AUDIO IN jacks on your TV, the
stereo light on the TV might not glow. If the Status Display indicates you are receiving stereo, you are. Details are on
page 39.
•
Only tapes recorded in Hi-Fi audio will play in Hi-Fi audio. Tapes recorded in normal audio will play in monaural
(single-channel) audio.
Cleaning the Video Heads
•
Your DVD/VCR automatically cleans the video heads of the VCR each time you insert a tape. However, the heads may
become dirty. If so, have an authorized servicer clean the video heads. Eventually, the heads may need to be replaced.
The playback picture is too dim, too bright or fluctuates in brightness.
•
Some programs may be broadcast with copyright protection technology in order to protect the rights of copyright
owners.This technology is used on programs that are recorded on video cassettes or DVDs, as well as some
programs broadcast by antenna/cable/satellite television channels. Programs broadcast with copyright protection may
not record clearly. Likewise, if you play a tape that is a recording of a copyright protected program, the picture may
not be clear.Tapes of copyright protected programs may have a picture that is dark or dim, or the brightness of the
picture may fluctuate. Therefore, avoid recording or playing copies of copyright protected programs.
70 Helpful Hints (cont’d)
E8A21UD_EN2 5/15/06 8:04 PM Page 70