Filter
Top Products
27
INITIAL SETUP
• Bypass: This is the default setting. If your receiver or processor is
equipped with 6-channel inputs and is capable of adjusting the bass
management settings (speaker size, output levels and delay times)
for its 6-channel analog inputs (sometimes called the 6-channel
DVD-Audio inputs during source selection), then we recommend
you leave this setting at the default Bypass, and adjust the bass
management settings on your receiver.
• Stereo: If your receiver or processor is not equipped with 6-channel
inputs at all, or if you wish to use the DVD 38 as the source for a
multiroom system, to connect it directly to your TV or for recording,
then change this setting to Stereo, which will send a downmixed 2-
channel signal to the Analog Audio Outputs, for use with any 2-chan-
nel analog input on your receiver. You may then select an analog sur-
round mode available on your receiver.
NOTE: The 2-channel downmix (Stereo mode) and the
5.1-channel presentation of multichannel audio discs (Bypass or
Bass Management On modes) are not available simultaneously.
With bass management on or in Bypass mode, the same front
left and right channel information will be available at both the 2-
Channel and 6-Channel left and right Analog Audio Outputs. No
center or surround information will be present in the signal out-
put at the 2-channel Analog Audio Outputs.
In Stereo mode, the downmixed 2-channel signal will be
available at both the 2-Channel and 6-Channel Analog Audio
Outputs, with no center or surround channel information
available at the 6-Channel Analog Audio Outputs.
Step Three – Audio Adjustments
This menu allows you to adjust bass management settings that control
the audio output of the 6-Channel Audio Outputs for speaker size,
output level and delay times. The proper adjustment of these settings
is key to optimal reproduction of DVD-Audio discs, when the DVD 38 is
used with a receiver or processor that does not have audio adjustment
capabilities for the direct inputs. These settings are only effective when
the Bass Management line of the AUDIO SETUP submenu is set to On.
IMPORTANT NOTE: In order to avoid audio problems, when
the DVD 38 is connected to a receiver that
does
have the
capability to adjust bass management parameters for its
multichannel inputs, it is preferable to use the receiver for
these adjustments. In that case, remember to set the Bass
Management setting in the AUDIO SETUP menu to Bypass.
If you make the adjustments using the DVD 38's settings, it is
important that the receiver's settings for the multichannel direct
inputs be disabled, or set to “Large” for the speaker sizes and
“0” for the level adjustments and delay times, unless these
settings are also used for the receiver’s other source inputs, in
which case they should be left the way you set them when you
configured your receiver. If you have any questions about the
capabilities of your receiver or processor, we recommend that
you consult its owner’s manual or the manufacturer’s Web site
for further information.
If your receiver does not have 6-channel analog inputs, make sure to
select Stereo for the Bass Management setting in the AUDIO SETUP
menu. Then connect the Analog Audio Outputs to any
2-channel analog inputs on your receiver.
Press the Setup Button to activate the Setup menu; then use the
⁄
/
¤
Navigation Buttons until the AUDIO ADJUSTMENTS submenu
is highlighted, and press the Enter Button. See Figure 25.
Figure 25 – Audio Adjustments Submenu
The following adjustments are available on the AUDIO ADJUSTMENTS
menu for each speaker position. Use the Navigation Buttons to select
the settings for each speaker. Press the Enter Button to display a drop-
down menu with the selections available for the setting. Use the
⁄
/
¤
Navigation Buttons to highlight the appropriate setting, and then press
the Enter Button to select it.
You will notice that the adjustments for speaker size and distance (used
to calculate delay times) are set in tandem for the front left and right
speaker pair, and for the surround left and right speaker pair. Changing
the settings for either speaker in these pairs also affects that setting for
the other speaker in that pair. For this reason, it is important to select the
same brand and model for both speakers in each pair, and also to place
them at about the same distance from the listening position.
Before proceeding with the DVD 38’s audio setup adjustments, we
recommend that you first use the menu system in your receiver to
ascertain the settings already established for “Speaker Size,” “Output
Level” and “Delay Time” (may be set as a distance). Record these
settings in Table A3 in the appendix to refer to during the configuration
process, or follow these steps to obtain the information:
1. Consult the frequency response specification (usually found in the
owner’s manual) for each of your speakers. Make a note of the
lowest frequency each speaker is capable of handling. For example,
if your speaker has a frequency response of 80Hz – 20kHz, then
80Hz is the lowest frequency it is capable of handling.
For your subwoofer, the important figure is the highest frequency it is
capable of handling. For example, if the subwoofer has a frequency
response of 25Hz – 150Hz, then 150Hz is the highest frequency
it can handle. Some subwoofers allow you to adjust the frequency
crossover. Consult the subwoofer’s owner’s manual for instructions on
setting its crossover, and use the approximate number you selected.
2. Measure the distance from each speaker to the listening position.
This is used for setting the delay.
DVD 38 OM(color).qxd 2/7/07 3:57 PM Page 27