Filter
Top Products
46
NS-24LD100A13 Insignia 24" LCD TV/DVD Combo
www.insigniaproducts.com
Remote control
General
The picture has a few bright
or dark spots.
• A few bright or dark spots on an LCD screen is
normal. It does not affect the operation of
your TV/DVD combo.
Good picture, but no sound.
• Increase the volume.
• Make sure that the sound is not muted.
• Make sure you do not have headphones
connected. When headphones are connected,
no sound comes from the TV/DVD combo
speakers.
• Make sure that the correct audio mode is
selected.
• Make sure that the audio cables are connected
correctly and securely to your TV/DVD combo.
• Make sure that the antenna or cable TV is
connected correctly and securely. See
“Connecting a cable or satellite box
” on page 9
or “Connecting an antenna or cable TV (no box)
”
on page 12
.
• If you are using an antenna, the digital channel
signal may be low. To check the digital channel
signal strength, see “Checking the digital signal
strength” on page 28.
• The audio cable(s) you are using may be bad. Try
a new set.
Poor picture.
• Make sure that the room is not too bright. Light
reflecting off the screen can make the picture
difficult to see.
• If an S-VHS camera or a camcorder is connected
while another connected device is turned on,
the picture may be poor. Turn off one or more
devices.
Good sound but poor color.
• Adjust the contrast, color, and brightness
settings. See “Adjusting the TV picture
” on
page 22
.
Audio noise.
• Other devices (for example, a surround sound
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV/DVD combo. Try
turning off one device at a time to determine
which device is causing interference. After you
have determined which device is causing
interference, move it further from the TV/DVD
combo to eliminate the interference.
No output from one of the
speakers.
• Adjust the audio balance. See “Adjusting sound
settings” on page 24.
• Make sure that the audio cables are connected
correctly and securely to your TV/DVD combo.
After images appear.
• Do not display a still image, such as a logo,
game, or computer image, for an extended
period of time. This can cause a permanent
after-image to be burned into the screen. This
type of damage is not covered by your warranty.
Problem Solution
Problem Solution
Remote control does not
work.
• Make sure that the power cord is correctly
connected to your TV/DVD combo and a power
outlet.
• Make sure that there are no obstructions
between the remote control and the remote
control sensor on the front of the TV/DVD
combo.
• Point the remote control directly at the remote
control sensor on your TV/DVD combo. For the
location of the remote control sensor, see
“Aiming the remote control
” on page 18.
• The supplied batteries are wrapped tightly in
clear plastic. Make sure that you have removed
this plastic from the batteries.
• Make sure that the batteries are installed
correctly. See “Installing remote control
batteries” on page 18.
• Replace dead batteries with new batteries. See
“Installing remote control batteries
” on page18.
Trouble programming your
existing universal remote
control.
• See instructions and a table of common codes in
“Programming a different universal remote
control” on page 49.
• Codes are subject to change. For up-to-date
codes, go to
www.insigniaproducts.com/remotecodes
• Replace dead batteries with new batteries. See
“Installing remote control batteries
” on page18.
• Refer to the User Guide that accompanied your
universal remote control and contact the
manufacturer if problems persist.
Problem Solution
No power.
• Make sure that the power cord is correctly
connected to your TV/DVD combo and a power
outlet.
• Unplug the power cord, wait 60 seconds, then
plug the cord back in and turn on your TV/DVD
combo.
• Other devices (for example, a surround sound
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV/DVD combo. Try
turning off one device at a time to determine
which device is causing interference. After you
have determined which device is causing
interference, move it further from the TV/DVD
combo to eliminate the interference.
“No signal” error
message is displayed.
• Press INPUT and make sure that you have
selected the correct input for the device or
service you are trying to use.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure that you have the correct input
selected to view channels from the cable or
satellite box.
After Auto Channel
Search, there are no
channels.
• Reception can vary by channel depending on the
broadcast power level of a given station. Contact
your cable or satellite TV provider.
• Make sure that the antenna or cable/satellite TV
is connected securely to your TV/DVD combo.
• Try replacing the cable between the
antenna/cable or cable/satellite box and your
TV/DVD combo.
NS-24LD100A13_12-0375_MAN_V1_ENG.book Page 46 Wednesday, September 19, 2012 12:46 PM