Mitsubishi Electronics WD-57833 Projection Television User Manual


  Open as PDF
of 96
 
4. TV Operation and Features 29
Note: Tooperateotheraudio/videodevicesusing
theTV’sremotecontrol:
• SeeAppendixD,“ProgrammingtheRemote
Control.”
• Seechapter6,“NetCommand,”forNetCommand
IR“Learning”ofdevicekeys.
• ForcontrolofIEEE1394devices,seechapter6,
“NetCommand.”
• ForHDMIdevicescompatiblewiththe
TV’sNetCommandforHDMIfeature,see
“NetCommandforHDMIDevices“onthispage.
23.
F1–F4
For devices under NetCommand control:
PerformNetCommand“Learning”toassignyour
choiceoffunctionstothe
F1
–
F4
keys.
For devices operating independently of
NetCommand:The
F1
–
F4
keysworkliketheA,
B,C,Dbuttonsonsomecableboxes,satellite
receivers,andDVDplayers.Programtheremote
controlforyourequipmentandtestthekeys.See
AppendixD,“ProgrammingtheRemoteControl.”
25. (
PAUSE
): FreezesabroadcastTVpicturewhen
noSplitScreenimageisdisplayed.WhenSplit
Screenisdisplayed,freezesthesub-picture.
Record/Playback Keys
Useanyofthesemethodstoenabletherecordingand
playbackcommands:
• ProgramtheremotecontrolforyourDVR,VCR,or
DVDplayer/recorderandsettheslideswitchto
VCR
,
DVD
,
CABLE/SAT
,or
AUDIO
asappropriate.
• PerformNetCommandIR“learning”forthedevice.
• ForcontrolofIEEE1394devices,seechapter6,
“NetCommand.”
• CheckHDMIdevicesforcompatibilitywiththeTV’s
NetCommandforHDMIfeature(seebelow).
24.
(
RECORD
):
RecordswithaVCRorDVR.
25. (
PAUSE
): PausesaVCR,DVR,orDVD.See
aboveforuseduringTVviewing.
26.
(
STOP
):StopsplayofaVCR, DVR, orDVD.
27.
(
REVERSE
): RewindsaVCR.Reversescansa
DVRorDVD.
28. (
PLAY
):PlaysaVCR, DVR,orDVD.
29.
(
FORWARD
):FastforwardsaVCR.Forwardscans
aDVRorDVD.
Remote Control, continued
Care of the Remote Control
• Useonlyalkalinebatteries.
• Bewithin20feetoftheequipment.
• Donotpresstwoormorebuttonsatthesametime
unlessinstructedtodoso.
• Donotallowunittogetwetorbecomeheated.
• Avoiddroppingonhardsurfaces.
• Donotuseharshchemicalstoclean.Useonlya
soft,lightlymoistenedcloth.
• Donotmixoldandnewbatteries.
Resetting the Remote Control
Iftheslideswitchissetto
TV
andtheTVdoesnot
respondproperly,resettheremotecontrol.
1. Pressandhold
POWER
forseveralsecondsuntilthe
buttonblinkstwiceandgoesoff.
2. Releasethe
POWER
button.
3. Presskeys
0 0 9 3 5
andthe
POWER
buttonwillblink
twicewhenyoufinishenteringthecode.While
enteringthecode,pauseforamomentbetween
eachkeypresstoensureitisrecognized.
Low-Battery Indicator
Ifyoupressakeyandthe
POWER
keyblinksfivetimes,
replacetheremotecontrol’sbatteries.
NetCommand for HDMI Devices
TheTV’sremotemayoperatesomefunctionsof
compatibleHDMIdevicesabletoreceivecommands
throughtheHDMIcable.Testyourequipmentwiththe
TV’sremotetofindoutwhichcommandsaresup-
ported.Seebelowforcommandsthatmaybeavail-
able,dependingontheindividualdevice.Youcanadd
commandsusingNetCommandIR“learning”aftercon-
nectingandplacingIRemittersforthedevices.
Press
PLAY
onthedeviceitselfto:
• TurnontheTVifnotalreadyon
• Switchtothedevice(noneedtodisplaytheInput
Selectionmenu)
• Beginplayofthedevice
VCR,DVD,andDVRfunctionsthatmaybeavailable:
Record/
Playback
Menu
Navigation
Channel Tuning Other
CH
/
GUIDE
ENTER
Digits
0–9
,
—
CANCEL
F1
(content)
—
CANCEL
(tocancel)
ENTER MENU
 previous next