Filter
Top Products
58
[[DVD/VHS]]
Advanced Operations
[RAM] [DVD-R]
You can transfer (dubbing) programs recorded on a tape onto a disc°
with one stroke of the button.
In One-Touch Dubbing, programs are automatically dubbed onto the
disc from the location of playback on the tape.
° Available discs for transfer (dubbing) from tape are DVD-RAM and
non-finalized DVD-R.
Preparation
≥Select the unit viewing channel (or the AV input) on the TV.
DVD
≥Release protection (disc l 30, cartridge l 18). [RAM]
≥Insert a disc and confirm there is sufficient empty space for
recording on it. (l 20, 47)
≥Select the recording mode.
≥When SAP broadcast program is played back on VHS, the audio
on DVD is recorded according to the settings in “Select MTS” in the
initial settings. (l 44) [DVD-R]
VHS
≥Insert the video cassette containing the program to be copied
(l 48).
[1] While both DVD/VHS are stopped,
Press and hold [“ DVD, DUBBING] for 3 seconds
or more.
On the main unit, press [“ DVD].
≥Check if transfer (dubbing) starts properly.
≥The “DUBBING” indicator on the main unit lights.
≥Dubbing is automatically completed when the tape reaches its
end or the disc becomes full.
∫To stop transfer (dubbing) halfway through
Press [∫, STOP].
≥When transfer (dubbing) is completed, a message indicating the
end of transfer (dubbing) appears on the TV screen and then
disappears a few seconds later.
∫When transfer (dubbing) is started, the following
operations also start automatically
≥“OSD” on VHS MENU ) “OFF” (l 56)
≥Recording channel indicator on DVD ) “TP”
≥Output to TV ) DVD output
∫Only the following operations are allowed while
transfer (dubbing)
≥Stopping transfer (dubbing) by pressing [∫, STOP].
Note:
≥While One Touch Transfer (Dubbing) is activated, a timer recording
cannot be started.
≥When “DVD/VHS Output” is set to “Manual” (l 43), or when VHS
output is selected in starting transfer (dubbing), the output is
switched to DVD automatically at the time when transfer (dubbing)
is started.
-
When the transfer (dubbing) is already started, you cannot switch
the output manually.
≥When the transfer (dubbing) is not started or not executed, the
“DUBBING” indicator blinks for about 7 seconds. Check if the unit is
properly prepared.
≥When a Copy-guarded tape is inserted, a message appears on the
display and the recording stops on the spot.
≥If a part of the tape recorded in VP mode is dubbed to disc, noises
may appear at the beginning of the dubbed part.
Transfer (Dubbing) from VHS
VHS
DVD
PROG/CHECK
DVD RECVHS REC
REC MODE
ADD/DLT
DUBBING
VHS DVD
TIME SLIP
CHAPTER
JET REW
STATUSDISPLAY
DVD ERASE
SKIP/INDEX
SLOW/
SEARCH
REW
FF
PLAY
FUNCTIONSDIRECT NAVIGATOR
TOP MENU
VHS MENU
POWER
CM SKIP
CANCEL/RESET
VOLUME
CH
INPUT SELECT
AUDIO
TV
TV/VIDEO
DVD/VHS
VHS
DVD
TRACKING/V-LOCK
DVD/VHS POWER
VCR Plus+
OUTPUT
REC MODE
1
;
∫
CH, W, X
µ, DVD REC
“ DVD
OPEN/CLOSE
TIME SLIP
REC
CH
/k1.3
DUBBING
VHS
DVD
DUBBING indicator
∫ One Touch Transfer (Dubbing) (VHS l DVD)
∫Dividing a title to be dubbed
In One-Touch Transfer (Dubbing) from VHS to DVD, the title is
divided by index signal detected and then recorded. You can
search desired titles with Direct Navigator’s Title View (l 33)
after transfer (dubbing) to DVD.
≥Titles recorded within 15 minutes (25 minutes in VP mode) of
each other may not be divided properly.
≥The recording time may become longer than the original title
depending on the number of index signals.
VHSDVD
PP-Sample.book 58 ページ ２００４年３月８日 月曜日 午後６時３分