Filter
Top Products
Playing back
23
RQT6570
[HDD] [RAM] [DVD-R] [DVD-V] [CD] [VCD]
1 Press [Í, DVD POWER] to turn the
unit on.
2 Press [HDD] or [DVD] to select the
playback drive
(➜ Drive, page 66).
The HDD or DVD button lights up on the unit.
≥It is not possible to playback both HDD (Hard Disk Drive)
and DVD drive simultaneously.
3 If you selected the DVD drive
Press [<, OPEN/CLOSE] to open the
tray and insert a disc (➜page 18).
≥Press the button again to close the tray.
≥Insert label-up. (Load double-sided discs so the label for the
side you want to play is facing up.)
≥It is not possible to play continuously from one side of a
double-sided disc to the other. You will need to eject the disc
and turn it over.
≥When using 8 cm (3
q
) DVD-RAM, remove the disc from the
cartridge and insert it, making sure you align it with the
groove.
≥If you put a disc in while the HDD is selected, the DVD but-
ton on the unit will flash while the unit reads the disc.
≥If Cartridge Protection is activated (➜page 8), pressing [<,
OPEN/CLOSE] will cause playback to begin automatically.
4 Press [1] (PLAY).
The unit takes some time to read the disc
before play starts.
≥If the resume function (➜ right) is not
active, playback will begin from the most
recently recorded program.
≥If you want to play the beginning of the disc (e.g., the first
program, chapter or title), select “PLAY FROM TOP” in the
FUNCTIONS window (➜page 53).
To stop play
Press [∫] (When “PLAY” flashes ➜ Resume Function, right).
≥The screen saver on the right may
appear when you stop play. Press [∫]
again and you can use this unit’s tuner to
watch television.
To pause play
Press [;].
Press again to restart play.
[Note]
≥If you select another drive while playback is in progress, playback
will be stopped. If using DVD-Video, the contents of the menu
screen may be returned to their initial state.
≥If a disc is loaded and DVD drive is selected, the unit will come on
and play will start when you press [1] (PLAY).
≥When you play a disc with an audio-only track, the video from the
previous disc may continue to be shown on the television.
≥Actual sound levels for DVD-Video are lower compared to televi-
sion broadcast or playback of other discs. To avoid a sudden
increase in volume level when switching from DVD-Video, reduce
the volume setting before playing other sources or switching to
television broadcast.
[DVD-V] [VCD]
[VCD]
Switch [DVD, TV] to “DVD” and
Press the numbered buttons (0, 1j9) to select an item.
e.g., “5”: [0] ➜ [5]
“15”: [1] ➜ [5]
[DVD-V]
Press [3, 4, 2, 1] to select an item and press
[ENTER].
≥You may also be able to use the numbered buttons (0, 1j9) to
select an item.
Other buttons used to operate menus
Read the disc’s instructions for further details about operation.
[9] [E]: Shows the next menu.
[:] [D]: Shows the previous menu.
[RETURN]: Shows the menu screen. [VCD]
[TOP MENU]: Shows the first menu screen. [DVD-V]
[MENU]: Shows the menu screen. [DVD-V]
[Note]
≥Discs continue to rotate while menus are displayed. Press [∫]
when you have finished viewing to preserve the unit’s motor and
your television screen.
≥If “/” appears on the television, the operation is prohibited by
the unit or disc.
≥Functions available vary from disc to disc.
[HDD] [RAM] [DVD-R] [DVD-V] [CD] [VCD]
(When the elapsed play time is displayed)
1 During play
Press [∫].
The unit memorizes the position.
2 While “PLAY” is flashing on the display
Press [1] (PLAY).
Play starts from where you stopped it.
To cancel the resume function
Press [∫] until “PLAY” goes out.
(The position is also cleared when you turn the unit off. When the
DVD drive is selected, the position is cleared if you open the disc
tray.)
To start play from a memorized position after turning
the unit off
Press [POSITION MEMORY] during play.
(The message “Position Memorized” appears on the television.)
Now when you press [1] (PLAY) after switching the unit to standby
and back on, play starts from the memorized position and the posi-
tion is cleared.
For your reference
If you press [∫] before switching the unit to standby after pressing
[POSITION MEMORY] to memorize a position, play will resume
from the position you pressed [∫] when you press [1] (PLAY).
[DVD-R] [DVD-V] [CD] [VCD]
≥The position is memorized when you press [POSITION MEMORY]
and cleared when you open the disc tray.
[RAM]
≥Positions recorded by pressing [POSITION MEMORY] remain
memorized even after the disc tray is opened.
≥You cannot mark positions if the disc is write-protected.
Subsequent to Resume Function (➜ right), reference is
made to steps 1-3 only where necessary.
!?
When a menu screen appears on the
television
Starting play from where you stopped it
—Resume Function
!?