Filter
Top Products
English
Searching for recorded video
25 How to use
1
Press the SEARCH button during recording or live
video.
2
Turn the J-dial, select "MOTION DETECTION
SEARCH", and turn the S-dial clockwise.
The <MOTION DETECTION SEARCH 1> screen
appears.
The "SEARCHING" starts blinking.
☞ Press the SEARCH button to cancel the search
mode.
Operation returns to the normal screen.
3
Turn the S-dial clockwise.
The "ALARM" starts blinking.
4
Select the desired recording area (example: ALARM
& NORMAL) by turning the J-dial, and then turn the
S-dial clockwise.
"SEARCHING" of END starts blinking again, the search
is over.
Selections: ALARM/NORMAL/ALARM & NORMAL
5
Select a channel by turning the J-dial and then turn
the S-dial clockwise.
The "– –" starts blinking.
6
Select the desired channel (example: camera 4) by
turning the J-dial, and then turn the S-dial
clockwise.
The cursor moves to the START PREVIEW field.
7
Turn the S-dial clockwise.
The screen switches to the <MOTION DETECTION
SEARCH 2> screen, and the channel 4 preview screen
is displayed.
8
Turn the S-dial clockwise, and set the number using
the J-dial. Turn the S-dial clockwise again, and
repeat this to set the date and time for the start of
the search.
Example: October 28, 2006 8:30pm
When the settings are complete, turn the S-dial
clockwise.
9
Repeat the same steps as shown at 8 to set the
end date and time for the search.
Example: November 29, 2006 8:30pm
The cursor moves to the MOTION SENSOR field.
À
Turn the S-dial clockwise.
The motion sensor setting screen is displayed.
Á
Setting the motion sensor
1 Turn the J-dial to move the cursor to the desired
position of the sensor, and then turn the S-dial
clockwise.
–: Sensor is not set
ú: Sensor is set
After switching the sensor from unset to set, the
same operation can be used to set sensors at other
locations.
2 Turn the J-dial to move the cursor to "LEVEL:
OFF", and then turn the S-dial clockwise.
The "OFF" starts blinking.
Selections: OFF/1/2/.../9/10 (low sensitivity)
3 Turn the J-dial to set "LEVEL: OFF" to [5], and
then turn the S-dial clockwise twice.
The <MOTION DETECTION SEARCH 2> screen
returns.
For searching the "PREVIEW" or "VIEW" screens,
continue at P26 without exiting the current search.
Â
Press the SEARCH button to exit the search mode.
The normal live video display returns.
E Motion detection search (continued)
SEARCH
(J)
(S)
<MOTION DETECTION SEARCH 1>
SEARCH FROM : ALARM
START : 01-01-06 00:40
END : 05-01-06 10:17
END : SEARCHING
MOTION DETECTION SEARCH
CHANNEL : --
START PREVIEW ->
START :
28-10-06 20:30
If you set the motion search to a specific channel
(camera number), only the video from the specified
channel will be played. The camera title, date and time
may not be displayed fully on the screen.
END :
29-11-06 20:30
<MOTION DETECTION SEARCH 2>
SEARCH FROM : ALARM & NORMAL/ CHANNEL : 4
START :
28-10-06 20:30
END :
29-11-06 20:30
MOTION SENSOR ->
PREVIEW ->
VIEW ->
MOVE:JOG SELECT:SHUTTLE
- - - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
LEVEL : OFF EXIT
- - - - - - - - - -
- - - - - - - - - -
- - - - - -
- - - - - -
- - - - - -
- - - - - - - - - -
- - - - - - - - - -
- - - - - - - - - -
LEVEL : 5 EXIT
(S)
(J)
SEARCH