Filter
Top Products
14
Before Using the Unit
Before Using the Unit
Setting the Line Mode
This unit is shipped with the line mode still unset.
Therefore you need to set the line mode before using the
unit. (The unit cannot be used unless the line mode is set.)
Once it is set, the line mode is retained even when the unit
is powered off.
Setting procedure
Use the following procedure to set the line mode.
1
Power the unit on.
“Select ----” appears in the time data display.
2
With the SHUTTLE button held down, rotate the jog
dial.
When you rotate the jog dial in the forward direction,
the “----” part of the display changes in the sequence
525U > 525J > 625. When you rotate it in the reverse
direction, the display changes in the sequence 625 >
525J > 525U.
3
When the desired setting appears, release the
SHUTTLE button.
“Push SET !!” appears.
To redo the selection
Repeat step 2.
4
Press the SET button.
“Turn OFF !!” appears.
5
Power the unit off, and then power it on again.
The selected line mode becomes available for use.
You can change the setting made with this procedure
by using basic menu item 013 “525/625 SYSTEM
SELECT.” See 8-2-2 “Basic Menu Operations” (page
88) for more information about how to make basic
menu settings.
Note
The line mode is not set, or is cleared, in the following
situations. Reset the line mode.
• The unit is powered off before performing step 4 in the
previous procedure.
• The “RESET ALL SETUP” command in the
maintenance menu (see page 106) is executed.
Settings affected by the line mode
The following settings are affected when the line mode is
changed.
• Alarm message language
525(J): Japanese
525(U)/625: English
• The following menu item names, setting values, or initial
setting values
Setting Line mode
525U 525(U): NTSC (areas outside Japan)
525J 525(J): NTSC (Japan)
REC
VARIABLE
PRESET
PB
L
MIX
R
MONITOR
NETWORK
LOCAL
REMOTE
ACCESS
PHONES
TOP
F REV F FWD
END
PREV
NEXT
PLAY
AUDI O
MONITOR SEL
METER SEL INPUT CH INPUT SEL
VIDEO
INPUT SEL
COUNTER
SELECT
SUB
CLIP
THUMB
NAIL
SET RESET
SHIFT
EJECT
HOLD
STOP
REC
S
H
U
T
T
L
E
J
O
G
V
A
R
MARK1
ESSENCE
MARK
CLIP
MENU
S.SEL
MARK2
IN OUT
ALL/CH-1 CH-2 CH-3 CH-4
OVER
dB
-12
-20
-30
-40
-60
0
CH
- 15
SG DATA
ANASDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH
- 26
SG DATA
ANASDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH
- 37
SG DATA
ANASDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH
- 48
SG DATA
ANASDI
HOURS MINUTES SECONDS FRAMES
AE8/EBU
VITC VITCCOUNTER REC INHVIUB
EDIT KEY INHREMOTE
[
9P iLINK
]
INPUT
i.LINK
SDI
1/2
5/6
3/4
7/8
625
525
IMX
[
50 40 30
]
DVCAM
4 8 CH
18 24 BIT
CMPST
Y-R,B
SG
ALARM
MONITOR
AUDI O
SYS MENU
MENU
45
1
2,3
POWER switch (rear panel)
Time data display
625 625: PAL
Item No. Item name
Basic menu
002 CHARACTER H-POSITION
003 CHARACTER V-POSITION
Extended menu
601 VITC POSITION SEL-1
602 VITC POSITION SEL-2
Setting Line mode