Filter
Top Products
42
3-2 Setup / 3-3 Setting the Date and Time
Chapter 3 Preparations
3-2 Setup
The principal setup operations before operating this unit
can be carried out using setup menus.
The setup menus of this unit comprise a basic setup menu
and an extended setup menu. The contents of these menus
are as follows.
Basic setup menu:
• Items relating to the hours meter
• Items relating to operation
• Items relating to menu banks
Extended setup menu:
• Items relating to control panels
• Items relating to the remote control interface
• Items relating to editing operations
• Items relating to preroll
• Items relating to disc protection
• Items relating to the time code, metadata, and UMID
• Items relating to video control
• Items relating to audio control
• Items relating to digital processing
For detailed information about the items, except for the
basic menu items relating to the hours meter, of these
menus and how to use them, see Chapter 8 “Menus.” For
detailed information about menu operations relating to the
hours meter, see 9-1-1 “Digital Hours Meter” (page 113).
This unit allows three different sets of menu settings to be
saved in what are termed “menu banks” numbered 1 to 3.
Saved sets of menu settings can be recalled for use as
required.
For more information about the menu banks, see “Menu
bank operations (menu items B01 to B13)” (page 90).
3-3 Setting the Date and
Time
When using this unit for the first time, you should set the
date and time as follows.
1
Holding down the SHIFT button, press the MENU
button.
The system menu appears on the monitor screen.
2
Select “DATE/TIME PRESET” using the F button or
f button, then press the g button.
The date and time setting screen appears on the
monitor, allowing you to set the following items.
• YEAR: Calendar year
• MONTH: Month
• DAY: Day
• TIME: Time
• TIME ZONE: Time zone (Difference from UTC)
3
Set the date, time and time zone.
You can change the setting of the flashing digits.
To change the flashing digits
Use the arrow buttons (G, g).
To increase or decrease the values of the flashing
digits
Use the arrow buttons (F, f) or jog dial.
4
Press the SET button.
The date, time and time zone settings are stored.
To return to the previous menu page
Press the MENU button.
To exit the menu
Press the MENU button twice in succession.
REC
VARIABLE
PRESET
PB
L
MIX
R
MONITOR
NETWORK
LOCAL
REMOTE
ACCESS
PHONES
TOP
F REV F FWD
END
PREV
NEXT
PLAY
AUDI O
MONITOR SEL
METER SEL INPUT CH INPUT SEL
VIDEO
INPUT SEL
COUNTER
SELECT
SUB
CLIP
THUMB
NAIL
SET RESET
SHIFT
EJECT
HOLD
STOP
REC
S
H
U
T
T
L
E
J
O
G
V
A
R
MARK1
ESSENCE
MARK
CLIP
MENU
S.SEL
MARK2
IN OUT
ALL/CH-1 CH-2 CH-3 CH-4
OVER
dB
-12
-20
-30
-40
-60
0
CH
-
15
SG DATA
ANASDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH
-
26
SG DATA
ANASDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH
-
37
SG DATA
ANASDI
AE8/EBU
OVER
dB
-12
-20
-30
-40
-60
0
CH
-
48
SG DATA
ANASDI
HOURS MINUTES SECONDS FRAMES
AE8/EBU
VITC VITCCOUNTER REC INHVIUB
EDIT KEY INHREMOTE
[
9P iLINK
]
INPUT
i.LINK
SDI
1/2
5/6
3/4
7/8
625
525
IMX
[
50 40 30
]
DVCAM
4 8 CH
18 24 BIT
CMPST
Y-R,B
SG
ALARM
MONITOR
AUDI O
SYS MENU
MENU
1
2,3
43