Filter
Top Products
Appendix C
Utilities
Specifying SCSI Parameters
181
I/O INFORMATION
BOOTABLE DEVICES
Order Media Type Path
----- ---------- ---------------------------------------
1 CDROM Acpi(HWP0002,0)/Pci(2|0)/Ata(Primary,Master)/CDROM(Entry0)
Seg Bus Dev Fnc Vendor Device Slot
# # # # ID ID # Path
--- --- --- --- ------ ------ --- -----------
00 00 01 00 0x1033 0x0035 XX Acpi(HWP0002,0)/Pci(1|0)
00 00 01 01 0x1033 0x0035 XX Acpi(HWP0002,0)/Pci(1|1)
00 00 01 02 0x1033 0x00E0 XX Acpi(HWP0002,0)/Pci(1|2)
00 00 02 00 0x1095 0x0649 XX Acpi(HWP0002,0)/Pci(2|0)
00 20 01 00 0x1000 0x0030 XX Acpi(HWP0002,100)/Pci(1|0)
00 20 01 01 0x1000 0x0030 XX Acpi(HWP0002,100)/Pci(1|1)
00 20 02 00 0x8086 0x1079 XX Acpi(HWP0002,100)/Pci(2|0)
00 20 02 01 0x8086 0x1079 XX Acpi(HWP0002,100)/Pci(2|1)
00 40 01 00 0x1000 0x0021 03 Acpi(HWP0002,200)/Pci(1|0)
00 60 01 00 0x1077 0x2312 02 Acpi(HWP0002,300)/Pci(1|0)
00 60 01 01 0x1077 0x2312 02 Acpi(HWP0002,300)/Pci(1|1)
00 80 01 00 0x1000 0x000F 01 Acpi(HWP0002,400)/Pci(1|0)
00 80 01 01 0x1000 0x000F 01 Acpi(HWP0002,400)/Pci(1|1)
00 C0 01 00 0x1000 0x0021 04 Acpi(HWP0002,600)/Pci(1|0)
00 E0 01 00 0x103C 0x1290 XX Acpi(HWP0002,700)/Pci(1|0)
00 E0 01 01 0x103C 0x1048 XX Acpi(HWP0002,700)/Pci(1|1)
00 E0 02 00 0x1002 0x5159 XX Acpi(HWP0002,700)/Pci(2|0)
System Wake-On-LAN: Enabled
In the preceding example, a single SCSI interface is shown in the listing. The information for both
channels of the SCSI interface is shown in bold, for highlighting purposes.
For each channel of the SCSI board, you need to note certain information. As an example, look at
the information for the SCSI interface (the first two bold lines). For each channel of this SCSI
interface, note the following information:
• Bus #—identifies the bus the device is on; for the SCSI interface, this is the same for both
channels. In this example, the bus number is 20.
• Dev #—the ID the device is assigned on the bus; for the SCSI interface, this is the same for
both channels. In this example, the SCSI interface is device 01.
• Fnc #—identifies the channel of the device (00 for channel A, 01 for channel B, and so on). In
this example, because the SCSI interface has two channels, one channel is 00 and the other is
01.
• Vendor ID—shows the device’s vendor ID; for the SCSI interface, this is the same for both
channels. For all the SCSI interface the ID is 0x1000.
• Device ID—shows the device ID; for the SCSI interface, this is the same for both channels. For
the SCSI interface the ID is 0x0030.
• Slot #—identifies the physical card slot in the server where the SCSI interface is installed; for
the SCSI interface, this is the same for both channels. In this example, the SCSI interface is on
the I/O baseboard therefore the in slot number is xx.
• Path—identifies the device’s path; for the SCSI interface, this is the same for both channels. In
this example, the SCSI interface path is Acpi(HWP0002,200)/Pci(1|0) for channel A and
Acpi(HWP0002,200)/Pci(1|1) for channel B.