Filter
Top Products
19
When DVDs encoded in Dolby Digital
or DTS are played, the Dolby Digital or
DTS bitstream is outputted from the
player’s optical or coaxial digital audio
output. When the player is connected to
a Dolby Digital or DTS decoder,
you can
enjoy theater-quality audio in your
home. An optical digital audio cable
or coaxial audio cable (not supplied)
is required for these connections, as
shown below. Only one connection is
needed, not both at the same time.
NOTE: With multiple video sources,
your audio/video receiver can be used
for selecting the video signal and rout-
ing it to the TV. Connect the Component
∞, Composite § or S-Video ¢ out-
put of the DVD280 to the correct video
input on your receiver, and the video
outputs of the receiver to your TV. For
more details, see the manual of your
audio/video receiver.
NOTE FOR ANALOG AUDIO: The con-
nection from the Analog Audio Output
£ to the TV is optional. If you plan
on using your DVD280 alone, without
turning on your complete system, this
connection must be made, unless
you’ve used the SCART ¶ connec-
tion; then you can turn up the TV´s
volume, as needed. The Analog Audio
Outputs £ may also be connected to
the standard analog left/right DVD or
CD inputs on your receiver or proces-
sor, if you wish to use the DVD280 as
the input for a multiroom system.
SETUP AND CONNECTIONS
Connecting to a Receiver/Amplifier With a Dolby Digital or DTS Decoder
NORTHRIDGE,CA, USA
DIGITAL
AUDIO OUT
OPTICAL COAXIAL
ANALOG
AUDIO OUT
L
R
S-VIDEO
Pr/Cr/R
Pb/Cb/B
Y/Y/G
VIDEO
VIDEO OUT
OUT
IN
REMOTE
CONTROL
SCART
TV
MODEL NO. DVD280
Made in China
Maunfactured under license from Dolby Laboratories,
"Dolby",and the double-D symbol are trademarks of
Dolby Laboratories,
Confidential unpublished works, 1992-1997 Dolby
Laboratories. All rights reserved.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
WARNING : SHOCK HAZARD - DO NOT OPEN
AVIS : RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKAN 1 LASER LAITE
KLASSE 1 LASER PRODUKT
SERIAL NO.
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION
c
DTS and DTS Digital Out are trademarks
of Digital Theater Systems Inc.
AC INPUT
100-240V~50/60Hz
20W
TV
To power outlet
(AC 230V/50Hz)
To S-video input
connector
To analog audio input
connectors
on TV or receiver
(red/white, optional only;
see NOTE above)
Front Speaker (Left/Right) Center Speaker Surround Speaker (Left/Right) Subwoofer
To video input
connector
(yellow)
Dolby Digital or DTS Decoder
DVD280
To coaxial digital audio input connector
To optical digital audio input connector
NOTE: Only one digital connection is
required. You may use either optical or
coaxial, according to the requirements
of your system.
To SCART
connector
To Y (green)/
Pb (blue)/Pr (red)
component video
connectors
å
∫
ç
∂
≠
ƒ
©
Connecting to a Receiver
When using the DVD280 with an
audio receiver or processor, connect
it as follows. First, make either the
SCART connection å or one of the
video connections (S-video ∫, com-
posite video ç or component video
∂) to the TV. If you will sometimes
use the TV without the audio compo-
nent and you did not choose the
SCART connection å, you may
optionally make the analog audio
connection ≠ to the TV. Second,
make either the optical digital audio
connection ƒ or the coaxial digital
audio connection ©, to the receiver
or processor. If your receiver or
processor is equipped with video
connections , you may optionally
make connections ∫, ç or ∂ to
the receiver, and then connect the
receiver’s video monitor output
to the TV.
DVD280 OM 7/12/04 4:41 PM Page 19