Filter
Top Products
14
Basic operations
Basic operations
In the following description, we assume that the buttons on the remote control unit are mainly used, however, you may
use the corresponding buttons on the front panel if available.
Before operation
Press DVD STANDBY/ON on the remote control unit or press STANDBY/ON on the front panel.
When the unit turns on, the STANDBY/ON indicator on the front panel, which illuminates in red during standby, lights in
green and each DISC indicator (1 to 7) shows the current status of whether a disc is set or not in the corresponding disc
tray.
• The first time you turn on the unit after connecting the power cord, the DISC 1 to 7 indicators are illuminated until the unit detects
that no disc is set in the corresponding disc tray. Once detecting the status, the unit memorizes it unless you unplug the power
cord, so the DISC 1 to 7 indicators show the status of corresponding disc trays correctly.
• You can turn on the unit by pressing the
3 button. In this case, the behavior of the unit after pressing the 3 button is the same as
pressing this button while the power is on.
• When any disc is on the disc tray, you can turn on the unit using the DISC 1 to 7 buttons corresponding to the loaded disc number.
The behavior of the unit after pressing these buttons is the same as pressing them while the power is on.
• You can turn on the unit by pressing the 0 OPEN/CLOSE button on the front panel. In this case, the disc tray carousel opens.
The opening display shown right appears on the TV screen.
The following message may appear at the bottom of the opening display
depending on the condition.
• NOW READING:The unit is reading the disc information.
• REGION CODE ERROR!:
The region code of the DVD VIDEO disc does not
match the unit. The disc cannot be played back.
• OPEN: The disc tray carousel is opening.
• CLOSE: The disc tray carousel is closing.
• NO DISC: No disc is loaded.
• RESUME STOP:
The resume mode is set to “DISC RESUME.”
NOTE
Make sure that the TV - DVD switch on the remote control unit is set to “DVD” when using the 5/∞/
2/3 and numeric buttons for controlling the unit.
Turning on/off the unit
NOTE
• Even if you press DVD STANDBY/ON on the remote control unit or STANDBY/ON on the front panel to turn off the unit,
the unit is not disconnected from the AC power source as long as it is connected to the wall outlet. This state is called the
standby mode. In this state, the unit consumes a very small amount of power.
TV DVD
TV2
2
TV1
1
TV3
3
TV5
5
TV4
4
TV6
6
TV8
8
TV7
7
TV9
9
TV0
0
TV-/--
10
MUTING
+10
TV/VIDEO
CANCEL
TITLE/
GROUP
RETURN
VFPAUDIOSUB TITLEREPEAT
ANGLEDIGEST
3D
PHONIC
ZOOM
AMP VOL
PROGRESSIVE
SCAN
fs/Rate
RM-SXV016J
REMOTE CONTROL
OPEN/
CLOSE
DISC
SELECT
TV DVD
NEXTPREVIOUS
SELECT STROBECLEAR
SLOW
-
SLOW+
VOL
-
VOL+
CH
+
CH
-
T
O
P
M
E
N
U
M
E
N
U
O
N
S
C
R
E
E
N
C
H
O
I
C
E
ENTER
STANDBY/ON
TV DVD
PAGE
DVD
STANDBY/ON
STANDBY/ON
STANDBY/ON
PROGRESSIVE
DVD AUDIO/DVD VIDEO/SUPER VCD/VCD/CD PLAYER
DISC 1 DISC 2 DISC 3 DISC 4 DISC 5 DISC 6 DISC 7 E
X
DVD AUDIO
STANDBY/ON
STANDBY/ON indicator
NOW READING
Message area