Filter
Top Products
48
206-4147
Installer Menu (Cont.)
• 6 = Scaler Model RJPs: DVI Mode
Enables RJP feature for use with reduced cable bundle models.
In this mode, when an HDMI/DVI source is connected to the
RJP, only digital video is expected via the HDMI cable. Analog
audio is provided via separate cable, from the source, connect-
ed to an RJP AUDIO IN. If no analog audio cable is connected,
tuner audio will be heard.
Notes:
See Reference section, “RJP Model List and Input Auto-sensing
Hierarchy.” If RJP AVAILABLE is set to 1, 2, 5, or 6, item 040
AUTO CAMPORT is automatically set to 0. Settings 1, 2, 5, and
6 allow the lodge staff to customize each STB’s RJP setup based
on customer requirements.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature on Function Menu, if Function
Menu is available. Set to 0 to disable SAP feature on Function
Menu, if Function Menu is available.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up.
• Set to 0 for Set By System.
• Set to 1 for 4:3.
• Set to 2 for 16:9 (Factory Default).
• Set to 3 for Just Scan.
• Set to 4 for Zoom.
Note: Only applies if item 106 ASP RATIO LOCK is disabled, set
to 0.
102 - ATSC BAND
Sets up STB to receive different types of incoming signals:
0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.
103 - ATSC TUNE MODE
Sets ATSC tuning mode: Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets Minor Start Channel number at power up. 0 = NTSC. If not
0, number selected is the digital channel’s Minor Start Channel
number.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
108 - PANEL COM (Panel Communication)
Sets the display panel baud rate:
0 = 1200, 1 = 2400, 2 = 9600 (default), 3 = 115200
110 - PANEL DELAY
Sets the delay time in seconds before the STB initiates RS-232
communication with the display panel after the STB/display is
turned ON. 8 seconds is the default.
111 - PANEL VOL PRE (Panel Volume Preset)
Preset the display panel volume to achieve volume levels in
parallel with external equipment. 79 is the default.
113 - PANEL TYPE
Selects the display panel type. See Reference section, “Display
Panel Type Specifi cations” to determine the appropriate setting
for the display panel being used. (Reference section, “RS-232
Display Panel Requirements,” also provides a list of compatible
displays.)
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for Normal. Set to 1 for Blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal. Set to 1 to load presets of all Installer Menu
item settings.
Warning: If set to 1, this will reload the factory
defaults and clear the Channel List, including any
assigned channel icons and custom channel labels.
118 - POWER SAVINGS
Default is set to 3. When the STB is in Standby mode, the MPI
card slot is powered by the Standby power supply and embed-
ded b-LAN is not powered. When the STB is in Power On mode,
the MPI card slot is powered by the main 12V power supply and
embedded b-LAN is powered. Note that the STB must be turned
ON in order to communicate with the embedded b-LAN module
for confi guration and control when POWER SAVINGS is set to 3.
• 1 = MPI card slot Standby Mode power provided from Standby
power supply, and embedded b-LAN is always powered.
• 3 = MPI card slot Standby Mode power provided from Standby
power supply, and embedded b-LAN is only powered when the
STB is turned ON.
Note: See Reference section, “b-LAN Setup and Overview,” for
further information.
119 - DATA CHANNEL
Set to 0 (default) to disable. Set to the RF channel number of the
Data Channel for Pro:Centric or E-Z Installation (splash screen,
confi guration, or fi rmware) data. The STB may take several min-
utes to load EPG data after AC power is initially applied.