Filter
Top Products
RQT8320
29
Only when you have set “Progressive” to “On” in the Setup
menu (Ô page 40).
By using the FUNCTIONS window you may access the main
functions quickly and easily.
1 While stopped
Press [FUNCTIONS].
Functions displayed depend on the type of disc.
2 Press [e,r] to select an item and
press [ENTER].
• If you select “To Others” and press [ENTER], the
following screen appears. Press [e,r] to select an
item and press [ENTER].
• If you press [RETURN], you can return to the
previous screen.
To exit the FUNCTIONS window
Press [FUNCTIONS].
Status messages appear on the television during operation
to show the condition of the unit.
Press [STATUS].
The display changes each time you press the button.
Picture menu–Change the picture quality
Playback NR
Reduces noise and picture degradation.
On ↔ Off
Progressive (Ô page 49)
Select “On” to enable progressive output.
Select “Off” if the picture is stretched horizontally.
Transfer [When “Progressive” (Ô above) is set to “On”]
Select the method of conversion for progressive output
to suit the type of title being played (Ô page 49, Film and
video).
When the output signal is PAL
• Auto: Automatically detects the film and video
content, and appropriately converts it.
• Video: Select when using “Auto”, and the video
content is distorted.
• Film: Select this if the edges of the
film content appear jagged or
rough when “Auto” is selected.
However, if the video content is
distorted as shown in the
illustration to the right, then select “Auto”.
• When the tray is opened, the setting will return to
“Auto”.
When the output signal is NTSC
• Auto 1 (normal):
Automatically detects the film and video
content, and appropriately converts it.
• Auto 2: In addition to “Auto 1”, automatically detects
film contents with different frame rates and
appropriately converts it.
• Video: Select when using “Auto 1” and “Auto 2”, and
the video content is distorted.
AV-in NR (Only when AV1, AV2, AV3 or DV is selected)
Reduces video tape noise while dubbing.
• Automatic:Noise reduction only works on picture input
from a video tape.
• On: Noise reduction works for any input video.
• Off: Noise reduction is off. You can record the
input signal as it is.
Sound menu–Change the sound effect
V.S.S.
(Dolby Digital, MPEG, 2-channel or over only)
Enjoy a surround-like effect if you are using two front
speakers only.
• Turn V.S.S. off if it causes distortion. (Check the
surround function on the connected equipment.)
• V.S.S. does not work for bilingual recordings.
Dialog Enhancer
(Dolby Digital, 3-channel or over only, including a center
channel)
The volume of the center channel is raised to make
dialog easier to hear.
Other menu–Change the display position
Position
1 - 5: The higher the setting the lower the on-screen menu
moves.
RAM -R -R DL -RW(V) +R +R DL +RW
DVD-V
DVD-A
-RW(VR)
RAM -R -R DL -RW(V) +R +R DL +RW DVD-V DVD-A
-RW(VR)
FUNCTIONS window
Status message
Playback
Recording
Delete
To Others
FUNCTIONS
Cartridge Protection Off
Disc Protection Off
DVD-RAM
ENTER
RETURN
Playback
Recording
Delete
To Others
VIDEO Plus
+
Record
Playlists
Flexible Rec
DV Auto Rec
Setup
DVD Management
FUNCTIONS
Cartridge Protection Off
Disc Protection Off
DVD-RAM
ENTER
RETURN
1:45 SP12:34:50 7/5
T12 0:01.23 SP
gg
g
T12 0:12.34 SP
DVD-RAM
Remain
REC
NICAM
L R
PLAY
Type of disc
Recording or play status/input channel
Date and time
Available recording time and
recording mode
Title number and elapsed
time during recording/
Recording mode
Title number and
elapsed time during
play/Recording mode
No display
TV audio type being received
(NICAM or MONO)
Selected audio type
The remaining time appears here
while stopped.
Using on-screen menus/FUNCTIONS window and Status message