Filter
Top Products
Using other functions
09
79
En
Switching the speaker terminals
If you selected Speaker B at Speaker system setting on
page 115, you can switch between speakers using the
SPEAKERS button. If you selected Normal(SB/FH),
Normal(SB/FW), Front Bi-Amp or ZONE 2, the button
will simply switch your main speaker terminals on or off.
The options below are for the Speaker B setting only.
1
•Use
SPEAKERS
on the front panel to select a
speaker system setting.
As mentioned above, if you have selected Normal(SB/
FH) or Normal(SB/FW), the button will simply switch
your main speaker terminal (A) on or off.
Press repeatedly to choose a speaker terminal option:
• SPA – Sound is output from the A-speaker
terminals (up to 7 channels (including surround back
channels), depending on the source).
• SPB – Sound is output from the two speakers
connected to the B-speaker terminals. Multichannel
sources will not be heard.
• SPAB – Sound is output from the A-speaker
terminals (up to 5 channels, depen
ding on the
source), the two speakers connected to the B-
speaker terminals, and the subwoofer. The sound
from the B-speaker terminals will be the same as the
sound from the A-speaker terminals (multichannel
sources will be downmixed to 2 channels).
• SP (off) – No sound is output from the speakers.
Using the MULTI-ZONE controls
The following steps use the front panel controls to adjust
the sub zone volume and select sources. See MULTI-
ZONE remote controls on page 80.
1Press
MULTI-ZONE ON/OFF
on the front panel.
Each press selects a MULTI-ZONE option:
• ZONE 2 ON – Selects your primary (ZONE 2) sub
zone
• ZONE 2&3 ON – Select both sub zones
• ZONE 3 ON – Selects your secondary (ZONE 3) sub
zone
• MULTI ZONE OFF – Switches the MULTI-ZONE
feature off
The MULTI-ZONE indicator lights when the MULTI-ZONE
control has been switched ON.
2Press
MULTI-ZONE CONTROL
on the front panel to
select the sub zone(s) you want.
If you selected ZONE 2&3 ON above, you can toggle
between ZONE 2 and ZONE 3.
BRIGHT
d
(Brightness)
Adjusts the overall brightness. –6 to +6
Default: 0
CONTRAST
d
Adjusts the contrast between light
and dark.
–6 to +6
Default: 0
HUE
d
Adjusts the red/green balance. –6 to +6
Default: 0
CHROMA
d
(Chroma
Level)
Adjusts saturation from dull to
bright.
–6 to +6
Default: 0
BLK SETUP
f
Corrects the black depth in the
brightness signal.
Normally select 7.5. If the dark
parts of the picture are all black
with this setting, select 0.
7.5
0
a.If the video picture deteriorates when this settings is switched ON,
switch it OFF.
b.• When set to a resolution with which the TV (monitor) is not
compatible, no picture is output. Also, in some cases no picture will
be output due to copyright protection signals. In this case, change
the setting.
• When AUTO is selected, the resolution is selected automatically
according to the capacity of the TV (monitor) connected by HDMI.
When PURE is selected, the signals are output with the same
resolution as when input (see About the video converter on page 27).
• If this is set to something other than AUTO, PURE and 480i/576i
analog signals are input, 480p/576p signals are output from the
component output terminals.
c.• If the image doesn’t match your monitor type
, adj
ust the aspect
ratio on the source component or on the monitor.
• This setting is only displayed when 480i/p or 576i/p video signals
are being inp ut.
d.This setting is only displayed when the video signals below are
being input:
• 480i, 576i, 480p, 576p, 720p, 1080i analog video signals
• 480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video
signals
e.• This setting is valid for component outputs and HDMI output.
• This setting have the effect only for pictures recorded in the
interlaced scan format (480i/576i or 1080i signals).
• P.MOTION is disabled when PCINEMA is set to ON.
f. You can’t use this setting when the HDMI or component video
signals are being input.
Setting What it does Option(s)
Note
1 • The subwoofer output depends on the settings you made in Manual speaker setup on page 114. However, if SPB is selected above, no sound
is heard from the subwoofer (the LFE channel is not downmixed).
• All speaker systems (except Speaker B connections) are switched off when headphones are connected.
SC-37_35_UXJCB.book 79 ページ ２０１０年３月９日 火曜日 午前９時３２分