Filter
Top Products
Controlling the rest of your system (In case of SC-37)
10
83
En
Chapter 10:
Controlling the rest of your system
(In case of SC-37)
Important
• This section includes explanations for the SC-37’s
remote control. For instructions for the SC-35’s
remote control, see Controlling the rest of your
system (In case of SC-35) on page 96.
About the Remote Setup menu
The Remote Setup mode is set by pressing the HOME
MENU button while pressing MULTI OPERATION. The
different items on the Remote Setup menu are described
below. For their setting procedures, refer to the
explanations for the respective items.
Note
•You can cancel or exit any of the steps by press and
hold MULTI OPERATION for a couple of seconds. To
go back a step, press RETURN.
•After one minute of inactivity, the remote
automatically exits the operation.
Setting What it does
PRESET
RECALL
Preset codes can be set for the various input
functions. The remote control codes of a number
of other devices (including products of other
brands) are preset in the remote control to allow
these devices to be operated. See “Selecting
preset codes directly” on page 84.
CODE
LEARNING
If the desired operations cannot be performed
even though you have set the preset codes, the
remote control signals of other devices can be
learned directly. See “Programming signals from
other remote controls” on page 85.
MULTI
OPERATE
A series of the remote control operations for
starting listening or viewing can be programmed.
Multiple remote control codes can be set for the
different input functions. See “Multi Operation and
System Off” on page 87.
SYSTEM
OFF
This is a function for automatically turning off the
power of devices connected to the receiver.
Multiple remote control codes can be set, as
desired. See “Multi Operation and System Off” on
page 87.
DIRECT
FUNC
This is a setting for changing only the remote
control unit’s operation screen, without changing
the receiver’s input, when the remote control
unit’s input function buttons are pressed. This is
convenient for using the remote control unit for
devices not connected to the receiver. See “Direct
function” on page 86.
RENAME The names of the input function buttons displayed
on the remote control unit can be changed as
desired. See “Renaming input function names
manually” on page 86.
SYNC
RENAMING
Input function names changed on the receiver can
be acquired by the remote control unit so that the
names are the same on the remote control unit.
See “Renaming input function names in
synchrony with the receiver” on page 93.
ERASE
LEARNING
This function is used to erase remote control
codes that have been learned. Codes learned for
the different input functions can be erased
individually. See “Erasing one of the remote
control button settings” on page 85.
IR/RF
SELECT
This function is for selecting wireless (RF) or
infrared (IR) as the remote control operating mode
for the different devices. See Operating this receiver
by RF communications and Operating other
components by RF communications on page 92
OPERATION
MODE
The remote control unit’s operation screen
switches automatically when the receiver’s input
is switched (This is only valid when the operation
selector switch is set to SOURCE). See “Setting the
remote control operation mode” on page 94.
KEY RESET This is a function for resetting preset codes that
have been set. Key resetting can be done for
individual input functions. See “Resetting the
input assignment of one of the input function
buttons” on page 86.
ALL RESET This is a function for resetting all remote control
unit settings you have made to the defaults set
upon shipment from the factory. See “Resetting
the remote control settings” on page 86.
READ
PRESET ID
The preset codes set for the different input
functions can be checked. See “Confirming preset
co
des” on page 86.
CHANGE
RC MODE
If you have multiple Pioneer receivers, amplifiers,
etc., this setting can be used to prevent other units
from operating simultaneously when the remote
control unit is operated. See “Operating multiple
receivers” on page 84.
EXIT
SETUP
Exits the setup menu.
Setting What it does
SC-37_35_UXJCB.book 83 ページ ２０１０年３月９日 火曜日 午前９時３２分