Filter
Top Products
PAGE 6
Installation Overview
•Unpack the HD Integrator Box System
and all accessories.
• Determine installation location for the
HD Integrator Box System, TV stand or
mount.
• Determine mounting and installation
requirements. If used, AC Power
source outlet, Antenna/Cable service
connectors, any external equipment
required for system or TV operation,
all necessary cables, wires, connectors
and any other additional required
hardware, etc.
Installation Overview & System Setup:
Questions to Consider Before
Installation
VESA Bracket
Does the VESA Bracket have to be
mounted to the TV? Y: Install VESA
Bracket on TV following the instructions
supplied with the bracket.
Yes___ No___
TV Stand
Does the TV have to be mounted on the
stand? Y: Mount the TV on the stand
following the instructions provided with
the TV stand.
Yes___ No___
Installer's Remote Control
Does the Installer have the optional
Installer's remote control available to
use to set up the TV (This is a must for
TV setup.)?
Yes___ No___
Master TV Setup
Will the Master TV's features setup be
cloned and copied to other identical HD
Integrator Box Systems?
Yes___ No___
LT2002 Quickset II Clone Programmer
To copy the TV's setup, the installer will
need a clone programmer. Is there a
Zenith LT2002 Clone Programmer
available?
Yes___ No___
End-User Remote Control
Will a remote control be provided to the
end user to operate the TV? (The remote
is included with the TV.)
Yes___ No___
End-User Menu Access
Will the end-user have access to all the
menus on the TVs from the front panel?
Yes___ No___
HD Integrator Box System Setup
Checklist
1. Install the HD Integrator Box System
where it will be used.
Prior to Operation
The HD Integrator Box System must be
connected to all external antenna/cable,
video, and audio source equipment.
See page 5, Table of Contents.
2. Make all external source equipment
connections. See pages 10 - 17.
3. Connect the HD Integrator Box
System to a standard 120V, 60 Hertz, AC
power source. See page 14.
4. Turn on the TV and all source
equipment.
Review TV Setup Options in the
Installer's Menu Section
The Installer's menu includes a number
of options for the master TV's setup that
enable the installer or system
administrator to devise a unique system
using the many different options and
variables available. See Installer's menus
section.
*Note:
If using the HCS5610 with a TV that has
Commercial Lite, Public Display Mode, select
'No'' for the Public Display Mode menu option
to disable
Public Display Mode.
Master TV Features Setup for Cloning
Overview
• Set up Installer's remote control, see
page 21.
• Do a Channel Search, see page 22.
• Channel List.
• Channel Label.
•Video/picture appearance options
setup, see Picture menu.
•Audio/sound options setup, see Sound
menu.
• Set up all other features. See page 5,
Table of Contents, for a list of features
available on this HD Integrator Box
System.
Clone Master TV's Setup
See Clone Programmer section.
*Note:
After installing a PPV card in the HCS5610
be sure to disconnect the AC power cord for
5 seconds and reconnect it.
Supplied Accessories List
- 5 ft. HDMI to DVI-M Cable
- 1 ft. HDMI to DVI-F Cable
- 5 ft. RS-232 Control Cable
- 6 ft. AC Power Cord
- 3 ft. IR Receiver Cable
- Screws & Wall Mount Bracket (5-
Required)
- 1 ft. RCA Jack to Stereo Plug
Cable(3.5mm)
- 5 ft. Stereo Plug to RCA Plug to Stereo
Plug(3.5mm)
- Installation Guide
- User Remote Control & Batteries
(Included)
- Installer Remote Control & Batteries
(Optional)
Setup Checklist