Filter
Top Products
91
Ⅵ DD: JVC STATUS SENSE
This section describes 4-byte data that are returned
when the STATUS SENSE command is sent.
7 Always 1
6 Always 0
5Unused : Always 0
4 DMF : Playing back LP-mode tape
3Unused : Always 0
2 JVC TABLE2 : JVC TABLE 2 enabled
1 JVC TABLE1 : JVC TABLE 1 enabled.
0 LOCAL : REMOTE switch set to LOCAL
ⅷ First byte
7 TC GENERATOR : Time code generator in the TCG
mode.
6 USER BIT : Counter mode set to the UB
mode.
5 TIME CODE : Counter mode set to the TC
mode.
4 CONTROL PULSE : Counter mode set to the CTL
mode.
3 CTL completion : Always 0
2DROP FRAME : Current time code in the DROP
FRAME mode
1LTC :Always 1
0Unused : Always 0
ⅷ Second byte
7 TC REC RUN : TCG set to the Rec Run mode
6 TC REGEN : TCG set to the REGENERATION
mode
5 TC EXTERNAL : TCG set to the EXT mode
4 TC INSERT LED : Time code insert edit mode
3AUD1 INSERT LED : Audio-1/2 insert edit mode
2AUD2 INSERT LED : Audio-3/4 insert edit mode
1 VIDEO INSERT LED:Video insert edit mode
0 ASSEM : Assemble mode
ⅷ Third byte
7 TBC PWB IN : Always 1
6 TC PWB IN : Always 1
5DA3 INSERT LED : Always 0
4DA4 INSERT LED : Always 0
3AUTO MODE : Auto editing/Previewing/Review-
ing
2Unused : Always 0
1Unused : Always 0
0Unused : Always 0
ⅷ Fourth byte
Ⅵ Setup (preset) commands
These commands are for setting various types of VCR
data. The commands corresponding to the settings
can be transmitted.
B
B
B
B
E0
E1
E3
E4
E5
E6
TC DATA PRESET :
For presetting the time code data. To
set, transmit the time data following
this command. Specify the time in or-
der of hour, minute, second and frame,
using two digits for each. When EN-
TER (40h) is transmitted before all dig-
its have been transmitted, the time
code data are specified by entering
digits from the uppermost digit.
TC UB DATA PRESET :
For presetting the user’s bit.
IN DATA PRESET :
For presetting the edit-in point. Set by
transmitting time data following this
command.
Specify the time in order of hour,
minute, second and frame, using two
digits for each.
If ENTER (40h) is transmitted before
all digits have been transmitted, this
command is executed with unspecified
parts set as “0.”
If this is a negative value in the CTL
mode, set 38h to the digit of 10H.
OUT DATA PRESET :
For presetting the edit-out point.
For details, refer to IN DATA PRESET
(E3h) above.
EDIT PRESET :
For selecting the edit mode. Each bit
is defined as shown in the table be-
low.
• ENTER (40h) is invalid.
PREROLL TIME PRESET :
For setting the preroll time. Specify this
by transmitting 2-byte data following
this command. First byte for ten’s place
and second byte for one’s place.
76 4
3210
0011
0 INS ASM Video
3210
0011
0TC
Aud-1 Aud-2
5
First
byte
Second
byte
Bit No. Status: If the bit is 1
Bit No. Status: If the bit is 1
Bit No. Status: If the bit is 1
Bit No. Status: If the bit is 1
Table Command Description
DV6000U_72-104_Eng.p65e 06/03/03, 11:42 PM91