Filter
Top Products
Masterpage:Right+
EN 39
Filename [M100_07Timer Recording.fm]
TIMER RECORDING
On-Disc Timer Programming is a function used with discs that are
especially intended for a specific program. The disc is then
programmed for a program you always watch every day or every
week. Since older programs are automatically overwritten, a single
disc can be used without worrying about how much recording
capacity remains. You can program each disc to timer record as
many as 8 programs up to 30 days in advance.
To Make The Disc For On-Disc Timer Programming
1 Press PROG to access
the Program Check
screen.
2 Press selection keys to
select ADISC TIMER
PRGMB, then press
ENTER.
● When some programs
are recorded on the disc,
a caution message
appears. To backup the recorded programs, press ENTER, and
perform dubbing to other devices.
● When On-Disc Timer Programming has already been made on
the disc, press selection keys to select ANEW TIMER
PROGRAMB, then press ENTER.
3 Press selection keys to
set the desired date
(ADATEB), then press E.
4 Press selection keys to
set the desired start time
(ASTARTB), then press E.
● Each press of FG
increases/decreases the
start time in 1-minute
interval.
● To increase/decrease the start time in 30-minutes interval,
press and hold FG.
5 Press selection keys to set the desired stop time (ASTOPB),
then press E.
● Each press of FG increases/decreases the stop time in 1-
minute interval.
● To increase/decrease the stop time in 30-minutes interval,
press and hold FG.
6 Press selection keys to set the desired channel (ACHB), then
press E.
7 Press selection keys to set ADAILY/WEEKLYB, then press E.
● For details on ADAILY/WEEKLYB setting, refer to “Daily/Weekly
Recording Function” (A pg. 37).
8 Set the other recording
options as required.
● “Recording Mode”
(A pg. 34)
● “Modify Title Name”
(A pg. 46)
9 Press ENTER to access
the Program
Confirmation screen.
10 Press ENTER to
complete the timer programming.
● To program another timer using “To Make The Disc For On-
Disc Timer Programming”, repeat steps 1 - 10.
11 Press DVD A to turn off the power.
● is displayed on the front display panel.
● To disengage the timer mode, press DVD A again.
On-Disc Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the TV and select an input mode such as EXT1.
● Load a DVD-RAM or DVD-RW (VR mode) disc for
programming.
ATTENTION:
● On-Disc Timer Programming is possible only with the disc for
On-Disc Timer Programming.
● If data is recorded on a disc for On-Disc Timer Programming
using a unit from another manufacturer, On-Disc Timer
Programming may not function properly.
PROG
Selection Keys (FGDE)
ENTER
DVD
A
Cable Box or DBS Receiver Users
To timer record a satellite broadcast using On-Disc Timer
Programming:
A Perform On-Disc Timer Programming.
● Set the channel to the external input (AL-1B or AF-1B)
connected to the cable box or DBS receiver.
B Set the cable box or DBS receiver to the appropriate channel
for recording.
● Leave the cable box or DBS receiver’s power on.
PROGRAM CHECK
DATE
++++++++++++++++++ NEW TIMER PROGRAM ++++++++++++++++++
START
CH
DAILY/WEEKLY
REC MODE
DISC TIMER PRGM
STOP
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
OK
SELECT
PROG
EXIT
DISC TIMER PRGM
DATE
START
STOP CH
10/07/03 THU - - : - - - - - - : - - - - - -
DAILY/WEEKLY
REC MODE
SP
NAME
SET TIMER PROGRAMING WITH [CURSORS]
THEN PRESS [ENTER]
CONFIRM
SELECT
PROG
EXIT
WEEKLY
DISC TIMER PRGM
DATE
START
STOP CH
10/07/03 THU - - : - - - - - - : - - - - - -
DAILY/WEEKLY
REC MODE
SP
NAME
SET TIMER PROGRAMING WITH [CURSORS]
THEN PRESS [ENTER]
CONFIRM
SELECT
PROG
EXIT
WEEKLY
M100_00.book Page 39 Friday, February 18, 2005 6:23 PM