Filter
Top Products
Filename [M100_10Subsidiary.fm]
Masterpage:Left0
58 EN
SUBSIDIARY SETTINGS
Various modes of this unit are categorized into menus nested in
2 levels shown in the following table. To change the settings of
these modes, find the desired mode in the menu, then follow the
procedure below. (For details on each menu, see pages 58
through 59)
● The procedure below shows how to set the desired option of the
“2ND AUDIO RECORD” mode as an example.
1 Press SET UP to access the Main Menu screen.
2 Press selection keys to select “FUNCTION SET UP”, then
press ENTER.
3 Press selection keys to
select “RECORDING
SET”, then press
ENTER.
4 Press selection keys to
select “2ND AUDIO
RECORD”, then press
ENTER.
5 Press selection keys to
select the desired
setting, then press ENTER.
6 Press SET UP to complete the setting.
*The boldface settings below indicate the settings at your purchase.
AUDIO OUTPUT
8 DIGITAL AUDIO OUT ^ DOLBY DIGITAL/PCM / STREAM/
PCM
/ PCM ONLY
Set to the appropriate mode according to the type of the device
connected to [DIGITAL OUT] connector.
DOLBY DIGITAL/PCM:
Select this when you connect the digital input connector of a
Dolby Digital Decoder or an amplifier with a built-in Dolby Digital
Decoder.
STREAM/PCM:
Select this when you connect the digital input connector of an
amplifier with a built-in DTS, Dolby Digital, or MPEG
multichannel decoder.
PCM ONLY:
Select this when you connect the linear PCM digital input of
other audio equipment (amplifier, MD or DAT deck, etc.).
NOTE:
If you watch or play back a program recorded on a DVD-RAM or
DVD-RW (VR mode only) disc which contains multiple audio
languages, select “PCM ONLY” in advance and choose main or
sub audio with AUDIO.
8 ANALOG AUDIO OUT ^ STEREO / DOLBY SURROUND
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
STEREO:
Select this when listening to conventional two-channel stereo
audio with the unit’s [AUDIO OUTPUT] connectors connected
to a stereo amplifier/receiver or TV set, or in case you want to
record the audio from a DVD VIDEO disc to a Mini Disc, etc.
DOLBY SURROUND:
Select this when listening to audio with the unit’s [AUDIO
OUTPUT] connectors connected to an amplifier/receiver with a
built-in surround decoder or a surround decoder.
8 D. RANGE CONTROL ^ NORMAL / WIDE RANGE / TV MODE
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a program
encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
NORMAL:
Normally select this setting to activate this function.
WIDE RANGE:
Select this to deactivate this function when you enjoy wide
dynamic range program.
TV MODE:
Select this when connecting to a TV. Even soft sound can be
well heard.
NOTES:
● This function has no effect on programs other than those
recorded in Dolby Digital format.
● The effect of “NORMAL” and “WIDE RANGE” may not be
different depending on discs.
8 OUTPUT LEVEL ^ STANDARD / LOW
You can lower the output level of analogue audio to accommodate
the unit to the connected A/V equipment.
STANDARD:
Normally select this setting.
LOW:
The output level of analogue audio is lowered.
Mode Set
● Turn on the unit.
● Turn on the TV and select an input mode such as EXT1.
DVD SET UP LANGUAGE SET (A pg. 18)
AUDIO OUTPUT (A pg. 58)
UTILITY (A pg. 62, 63)
FUNCTION SET UP VIDEO IN/OUT (A pg. 21, 59)
RECORDING SET (A pg. 59)
DISPLAY SET (A pg. 59)
OTHERS (A pg. 60)
INITIAL SET UP TUNER SET (A pg. 20)
CLOCK SET (A pg. 19)
Selection Keys (FGDE)
ENTER
SET UP
AUDIO
DVD SET UP
SAVE AS LIBRARY
FUNCTION SET UP
INITIAL SET UP
XP MODE REC AUDIO
VIDEO IN/OUT
ON
DOLBY DIGITAL
2ND AUDIO RECORD
RECORDING SET
DISPLAY SET OTHERS
OFF
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
OK
SELECT
EXIT
SET UP
OFF
ON
M100_00.book Page 58 Friday, February 18, 2005 6:23 PM