Filter
Top Products
Masterpage:Right+
EN 37
Filename [SR-MV40U_07DVD Operation2.fm]
Page 37 November 25, 2005 11:19 am
OPERATIONS ON DVD DECK
Watch Another Program While Recording On The Unit
While recording is going on, you can watch another program on the
TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (੬ pg. 66)
1 During recording, press TV/VCR to select TV mode if your unit
is connected to the TV via the RF connection.
● VCR mode is disengaged, then the VIDEO indicator lights off and
“TV” appears on the front display panel.
● The program received on the TV’s tuner is displayed on the TV
screen.
2 Slide the TV/CABLE/DBS/DVD switch to TV.
3 Press CH +/– repeatedly to select the desired channel.
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of disc
remaining times for all recording modes appears on the TV screen.
Free Rate Function
To record the entire program, the unit automatically set the
appropriate recording mode depending on the combination of the
total time of the program to be recorded and either the remaining
disc space or the specified recording time (from 60 minutes to 480
minutes).
8 To record the entire program within the actual remaining
disc space
Select “FR (JUST)” in a recording mode selection procedure.
(੬ pg. 38, 39)
● Note that this function is available only for timer programming
recording.
8 To record the entire program by specifying the desired
recording time
Select “FR60–FR360”, “FR420” or “FR480” in a recording mode
selection procedure. (੬ pg. 36, 38, 39)
8 To record a 25-min. long daily program five times just on a
same disc for example
Perform “VCR Plus+ Timer Programming” (੬ pg. 38) procedure.
Be sure to set the recording mode to “FR125” and set Weekly/Daily
Rec Function to “MON–FRI” in step 6 to fit the total recording time
to the whole disc space.
When the same program is recorded in SP mode instead of in
“FR125”, the 5th program cannot be recorded.
NOTES:
● You can program this unit to timer record, regardless of the disc
remaining time. When the disc remaining time is not enough,
recording may stop in the middle of a program. To avoid this, make
sure of the disc remaining time before setting timer programming.
(Example) If you programmed to timer record for 60 minutes in SP
mode on a 120-minute disc, the disc remaining time would be 30
minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP
mode, 180 minutes in EP mode, and 240 minutes in FR480 mode.
Timer recording will not complete beyond these remaining times.
● The maximum recording time of FR (JUST) mode is the same as the
recording time of FR480 mode. When timer programming a long
program in FR (JUST) mode on a disc whose remaining time is short,
it is recommended checking the disc remaining time in FR480 mode
to see if the remaining time is enough for the program.
● Even if more than one program are timer programmed in FR (JUST)
mode, only the first one is recorded.
● In order to ensure that the recording fits on the disc, this feature may
leave a slight non-recorded section at the end of the disc.
● There may be some noise and sound disturbance at the point on the
disc where the unit switches the mode.
Second Audio Recording
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set “2ND
AUDIO RECORD” to “ON”. (੬ pg. 70)
NOTE:
When the channel is changed on the unit;
● The “MONO” indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
● Both “MONO” and “SAP” indicators appear when the main audio on
the monaural broadcast is accompanied by SAP sound.
Recording Features
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press VCR/DVD repeatedly so that the DVD lamp lights up on the
unit.
1
4
7
2
5
8
0
3
6
9
CH +/–
DISPLAY
REMAIN
TV/VCR
VIDEO indicator lights off.
Blank
A: 1st
B: 2nd
C: 3rd
D: 4th
E: 5th
A: 1st
B: 2nd
C: 3rd
D: 4th
E: Blank (20 min.)
Blank
SR-MV40US.book Page 37 Friday, November 25, 2005 11:19 AM