Filter
Top Products
Filename [SR-MV40U_08VCR Operation.fm]
Masterpage:Left+
50 EN
Page 50 November 25, 2005 11:19 am
OPERATIONS ON VCR DECK
Check, cancel and change programs
1 When the VCR timer indicator lights on the front display
panel
Press VCR TIMER (#), then press 1.
When the VCR lamp does not light up on the unit
Press VCR/DVD repeatedly so that the VCR lamp lights up on the
unit.
2 Press PROG/CHECK to access the
Program Check screen.
To cancel a program
Press CANCEL to cancel a program.
3 Press rt to select the program,
then press ENTER. The program
screen appears.
4 Change the settings of the desired
recording options as required.
● Refer to steps 7 – 10 in “Manual Timer
Programming” (੬ pg. 49).
5 Press PROG/CHECK to complete
timer correction. The previous screen resumes.
6 Press VCR TIMER (#).
● The VCR timer indicator lights up on the front display panel and the
DVD deck is automatically selected. When the DVD deck is in timer
standby mode, the unit is automatically turned off.
When Programs Overlap Each Other
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, you have another program overlapping the program you
have just made.
The Program Check screen appears and conflicting programs will
start blinking.
Example: Program 1 (you have just made) and Program 4
overlap each other.
1 Confirm the overlapping programs. Overlapping programs blink
on the TV screen.
2 Press rt to select the program to modify, then press ENTER
or e.
● You can only select one of the overlapping programs.
NOTE:
If you do not mind this overlap, press PROG/CHECK to finish the timer
program setting. The program with the lower program number will be
recorded and the other one will not be recorded correctly. If no changes
are made for approximately 1 minute, the unit will return to the normal
screen.
3 Press rt to select the desired program to be cancelled or
changed.
To cancel the program
Press CANCEL.
● “PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen resumes.
To change the program setting
Press ENTER, then go to step 4.
4 Change the program setting.
● Refer to steps 7 – 10 in “Manual Timer Programming” (੬ pg. 49).
5 Press PROG/CHECK to check if the conflict has been settled.
Program check screen appears.
● “PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen resumes.
6 Press VCR TIMER (#).
NOTE:
When any overlaps remain after deletion and modification of programs,
Program Check screen remains showing the conflicting programs. In
such a case, repeat the procedure above until the conflict is solved.
1
4
7
2
5
8
0
3
6
9
PROG/CHECK
ENTER
CANCEL
VCR TIMER (#)
rtw e
VCR/DVD
1
(PROG/CHECK) TO NEXT
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4
5
6
7
8
PROGRAM 4
START STOP
8:00AM 10:00AM
DATE CH SP/EP
12/24/04
12 SP
FRI
PRESS (CANCEL) TO CANCEL
PRESS (ENTER) TO CONFIRM
(PROG/CHECK) TO END
( )](ENTER) (PROG) : END
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4 9:00P 10:00 10 12/24
5
6
7
8
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
SR-MV40US.book Page 50 Friday, November 25, 2005 11:19 AM