Filter
Top Products
25
Timer Recording With VCR Plus
Remote Control
POWER
Button
Number
Buttons
STATUS/
EXIT
Button
t_®-¢
VCR
PLUS+/
-ENTER
Button
MENU
Button
_CLEAR
Button
oo*o*ololoaeoooooo_olool oooooo OOOOIllOGOOOQ
• If you make a mistake while you are
entering the VCR Plus+ number of a
program, press the CLEAR button until
the cursor is flashing on the item you
want to correct. Then enter the correct
number.
• If CODE ERROR flashes after you enter
the VCR Plus+ number and press the
VCR PLUS+/ENTER button, the number
you entered was incorrect (for example,
too short). If this happens, enter the
correct number.
• CLASH ma_flash on the screen at step
2. This means that the timer recording
you just programmed and another timer
recocding overlap, and thus the current
timer recording will not be carried out.
• To quit VCR Plus+ programming at any
time, press the STATUS/EXIT button.
The display will disappear from the TV
screen.
• If the preset time for a timer recording
comes up during an OTR, the OTR has
priority.
• To stop a started timer recording, press
the STOP/EJECT button on the VCR.
• If the power fails for more than one
minute, programmed timer recordings
will be lost. When you use the VCR
with the auto clock function turned
OFF, repeat the steps on page 10 before
re-programming the timer recordings.
• To cancel a Timer Recording with VCR
Plus+, follow the steps for Checking or
Clearing Timer Recordings on page 20.
See page 35for more notes.
Follow the steps below to program a _l
timer recording using VCR Plus+ num-
bers. Before you begin, make sure:
• Channels have been programmed.
• The clock has been set.
• There is a tape in the VCR. Make sure
the tape's record tab is intact and the
tape is long enough to record the pro-
gram(s).
• The VCR is in VCR position.
• You have selected CABLE TV or TV
at the TUNER SET UP menu.
• You have completed the steps on
pages 22-24.
You must do each step within 60 sec-
onds of completing the previous step.
Jill
If you don't, you will have to start
again at step 1.
Press the VCR PLUS+/ENTER button
on the remote control. The on-screen
display shown below will appear.
LUScoo_._.... -j
FND PUSH EXIT
2
Use the Number buttons to enter the
VCR Plus+ number of the program
you wish to record (this number is dif-
ferent for every program, and it can be
four to eight digits long). Finally,
press the VCR PLUS+/ENTER button.
,_VCR PLUS+PROG.
J
PLUSCODE: 132B_::._::.-
TOSET PUSHVCR +
TOCORRECT PUSHCLEAR
END PUSH EXIT
3
To record the program once, press the
Number 1 button to select ONCE. To
• record the same program every day from
Monday through Friday, press the
Number 2 button to select DAILY. To
record the same program every week on
the same day (such as every Saturday),
i press the Number 3 button to select
Press the Number l button to record in
SP speed, press the Number 2 button to
record in LP speed, or press the
Number 3 button to record in SLP
speed. For details, see page five. You
cannot use the (Tape) SPEED button at
this time.
PRoGETIME PROGRAM 1
EL 9
TIME ON 10:30PM
TIME OFF 11:30PM
END PUSHEXff "
Press the STATUS/EXIT button. PRO-
GRAM WAS COMPLETED /
PLEASE TURN OFF VCR FOR
TIMER RECORDING should appear
on the screen. After three seconds, the-
on-screen display will disappear.
6
To program additional timer recordings
with VCR Plus+, press the VCR
PLUS+!ENTER button and repeat steps 2-
5. When you are finished, go to step 7.
7
Turn off the VCR power. The Timer
light will appear. The Timer light will
flash if there is not a tape in the VCR.
The VCR must be turned off for a
timer recording to take place. If you
forget to turn the VCR off, PLEASE
TURN OFF VCR FOR TIMER
RECORDING flashes on your TV
screen two minutes before a timer
recording starts. You can remove it by
)ressing the CLEAR button.
The VCR
must be off for a
timer recording
to take place!
Make sure there
is a taoe in the