Filter
Top Products
16
RQT6986
Recording
Recording television programs
[HDD] [RAM] [DVD-R]
Preparation
≥Connect a video cassette recorder to this unit’s input terminals
(➜page 60).
≥Press [HDD] or [DVD] to select the recording drive.
1 While stopped
Press [INPUT SELECT] to select the
input channel for the equipment you
have connected.
Select L1, L2, L3 or DV.
≥You can also select the input channel by pressing [W, X, CH].
2 Press [REC MODE] to select the
recording mode (XP, SP, LP or EP).
3 Start play on the other equipment.
4 Press [¥, REC] at the point you want
to start recording.
Recording starts.
To skip unwanted parts
Press [;] to pause recording. (Press again to continue recording.)
To stop recording
Press [∫].
[Note]
≥When recording using L1, L2 or L3 terminals, only the sound
received at the time of recording will be recorded.
≥The audio recorded through the DV Input terminal is the audio
selected in the “Select Audio CH for DV input” (➜page 53).
≥If flexible recording (➜page 15) is used instead of steps 2 and 4,
settings can be made so that recording continues to the end of the
video.
[HDD] [RAM]
Automatic generation of programs and play lists is possible for using
the “DV AUTO REC” function when connecting DV equipment (e.g.,
Digital Video Camcorders) to the DV input terminal on the front of
the unit with the DV cable.
Preparation
1. Turn off the main unit and DV equipment, then connect the
equipment with the unit’s DV input terminal. (➜page 60)
2. Turn on the main unit and DV equipment.
3. Pause play of the DV equipment at the point you want recording
to start.
4. Press [HDD] or [DVD] to select the recording drive.
1 While stopped
Press [FUNCTIONS].
The FUNCTIONS window appears (➜page 50).
2 Press [3, 4, 2, 1] to select “DV
AUTO REC” and then [ENTER].
DV AUTO REC screen appears.
3 Press [REC MODE] to select the
recording mode (XP, SP, LP or EP).
4 Press [2, 1] to select “Rec” and then
[ENTER].
Recording starts.
When recording finishes
The confirmation screen appears. Press [ENTER] to finish DV auto
recording.
To stop recording
Press [∫].
[Note]
≥Select the type of audio recording from the Audio menu’s “Select
Audio CH for DV input” settings (➜page 53).
≥You cannot record SD VIDEO (MPEG4) programs using “DV
AUTO REC”.
≥When “Cannot detect DV connection” is displayed or there is a
recording problem, confirm the connections, DV equipment set-
tings and reset the power.
If that does not work follow the instructions for “Recording from a
video cassette recorder” (➜left).
≥It is not possible to carry out Chasing play or Simultaneous rec
and play of the program that is being recorded.
≥The DV equipment name may not be shown correctly.
≥You cannot start recording until the images from the DV equipment
appear on the television.
≥Do not operate the DV equipment during recording, as this will
cause recording to stop.
≥Recording may not be performed as desired if the time codes on
the tape in the DV equipment are not successive.
≥During copying, a marker is automatically assigned to points in the
original recording where recording was stopped or paused.
≥The date and time information on the tape of the DV equipment
will not be recorded.
≥Depending on the equipment, the DV Automatic Recording may
not operate properly.
Recording from a video cassette recorder
DVD
TV
INPUT SELECT
VCR Plus+
OPEN/CLOSE
TV/VIDEO
CH
VOLUME
SKIP
DIRECT NAVIGATOR
PLAY LIST
TOP MENU
ENTER
MENU
FUNCTIONS
RETURN
STOP
PAU S E
PLAY/x1.3
SLOW/SEARCH
CANCEL
123
DVD TV
4
5
6
789
0
100
FRAME
CM SKIP TIME SLIP
ERASE
REC
PROG/CHECK
ADD/DLT
DUBBING
REC MODE
STATUS
MARKER
AUDIO
SETUP
DISPLAY
POSITION
MEMORY
POWER
3, 4, 2, 1
ENTER
FUNCTIONS
HDD DVD
W, X, CH
¥, REC
REC MODE
INPUT SELECT
HDD, DVD
;
∫
DV Automatic Recording (DV AUTO REC)
DV AUTO REC