Panasonic WV-CU360C Home Theater Server User Manual


 
67
o Joystick Controller (UP/DOWN/L/R)
Used to manually operate the Pan/Tilt Head, or move
the cursor in the camera menu on the active monitor
screen.
UP: Upward
DOWN: Downward
L: Left
R: Right
!0 Iris buttons (IRIS, CLOSE/OPEN)
Closes or opens the lens iris of cameras equipped with
the specified lens.
When these buttons are pressed at the same time, the
lens iris is reset to the factory default setting.
!1 Focus buttons (FOCUS, NEAR/FAR)
Adjusts the lens focus of cameras equipped with the
specified lens.
When these buttons are pressed at the same time, the
lens focus is set automatically if the specified camera
with the auto focus feature is equipped.
!2 Zoom buttons (ZOOM, WIDE/TELE)
Zoom the image in or out if the camera is equipped with
the specified lens.
!3 Programme Preset button (PROGRAM PRESET)
In combination with the numeric buttons and CAMERA
(ENTER) button, saves a preset position of the camera
in a system equipped with the specified cameras.
To save a preset position, move the camera to the posi-
tion to be preset and select a preset number by press-
ing the numeric buttons. Hold down the PROGRAM
PRESET button, then press the CAMERA (ENTER) but-
ton.
!4 Call Preset button (CALL PRESET)
In combination with the numeric buttons, moves the
pan/tilt head of the selected camera to a preset position
in a system equipped with the specified cameras.
!5 Camera/Enter button [CAMERA (ENTER)]
CAMERA: Used for camera selection. Select a camera
by pressing the corresponding numeric buttons, fol-
lowed by the CAMERA (ENTER) button.
ENTER: In combination with the numeric buttons, enter
numeric input, such as operator ID and password.
It is also used to execute the currently highlighted
selection and enter a submenu of the camera
menu.
Pressing CAMERA (ENTER) while holding down the
SHIFT button will activate the auto panning function of
the selected camera (AUTO PAN).
!6 Clear/Escape button [CLEAR (ESC)]
Clear: Clears numeric input from the LED display.
Escape: Escapes from the currently highlighted selec-
tion and return to the previous page of the camera
menu.
This button is also used to exit from alarm selection
mode to normal operation mode.
!7 Numeric buttons (0 - 9)
Used for numeric input into the system such as the
camera and monitor number, sequence number, preset
position, etc.
Pressing the buttons shown below while holding down
the SHIFT button will select special functions.
1: Turns off the user auxiliary 1 switch of the receiver.
(AUX1 OFF)
2: Turn on the user auxiliary 1 switch of the receiver.
(AUX1 ON)
3: Turns on the housing wiper of the camera until
these buttons are released. (WIPER)
4: Turns off the user auxiliary 2 switch of the receiver.
(AUX2 OFF)
5: Turns on the user auxiliary 2 switch of the receiver.
(AUX2 ON)
7: Turns off the housing defroster of the camera. (DEF
OFF)
8: Turns on the housing defroster of the camera. (DEF
ON)
!8 Shift button (SHIFT)
Pressing this button in combination with buttons to
which a special function has been assigned will acti-
vate these functions.
!9 Alarm button (ALARM), Disarm indicator (DISARM)
In combination with the Numeric buttons, selects an
alarm. To select an activated alarm, press the numeric
buttons, followed by the ALARM button.
Pressing this button repeatedly enables or disables the
cameras and monitor assigned to perform the alarm
activities.
The DISARM indicator next to the button is lit while
alarm activities are disabled.
@0 Alarm Acknowledge button (ACK)
Acknowledge an activated alarm. Select the alarm by
pressing the numeric buttons, followed by the ALARM
button. Select the desired alarm action number by
pressing the numeric buttons, then press the ACK but-
ton. The ACK indicator will light.
After acknowledging the alarm, press the RESET button
to reset the alarm. The ACK indicator will go off.