Filter
Top Products
The Initial Setup menu
13
95
En
English
Set the date (day/month/year) and time, then
press ENTER to make all the settings.
Use the
/
(cursor up/down) buttons to change
the value in the highlighted field.
Use the
/
(cursor left/right) buttons to move
from one field to another.
Input Line System
• Default setting:
625System
For standard PAL or SECAM recording, leave the input
line system to
625System
. When recording an NTSC or
PAL–60 signal through an external input, change to
525System
.
Note
• When the current input is a built-in tuner channel
preset, changing the input line system will usually
also affect the input line system of the
AV2/(INPUT
1/DECODER)
input. However if the
AV2/L1 In
setting
is set to
Decoder
(see
AV2/L1 In
on page 99), then the
L2 input is affected instead.
• If when this setting is changed, the screen goes
blank (due to incompatibility with your TV), you can
switch back by pressing and holding
STOP REC
then pressing
HDD/DVD
while the recorder is
stopped.
• When you switch the Line Input System setting the
Copy List is erased. If you switch the setting using the
STOP REC
and
HDD/DVD
buttons as described
above, there is no confirmation, so please use with
care.
• You can’t mix recordings of different TV line systems
on the same disc.
• When you change this setting, the
Input Colour
System
setting also changes (see
Input Colour
System
on page 99).
On Screen Display
• Default setting:
On
On the default setting, the recorder shows on-screen
operation displays (
Play, Stop
and so on). Change to
Off
to hide these displays.
Front Panel Display
• Default setting:
On
On the default setting, the time is shown in the front
panel display when the recorder is in standby. Switch to
Off
to have the front panel display switch off completely
when in standby.
Note
• When set to
Off
, the display still lights dimly in
standby when setting a timer recording, or during
Auto Start Recording.
Power Save
• Default setting:
Off
When set to
Off
, signals arriving at the
ANTENNA IN
terminal and at the
AV2/(INPUT 1/DECODER)
AV
connector are passed through to the
ANTENNA OUT
terminal and to the
AV1(RGB)-TV
AV connector,
respectively, when the recorder is in standby.
You can cut the standby power consumption of the
recorder by turning off the through function for one or
both terminals:
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
Clock Setting
Manual Clock Setting
2/2
Date
Time
Time Zone
Summer Time
01 01 2003
WED
00 00
Austria
Vienna
On
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
525System
625System
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
On
Off
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
On
Off
Initial Setup
Basic
Tuner
Video In/Out
Audio In
Audio Out
Language
Recording
Playback
Clock Setting
Input Line System
On Screen Display
Front Panel Display
Power Save
Remote Control Set
Setup Navigator
Mode1
Mode2
Off
Initial Setup
DVR-03_HDD_EU.book 95 ページ ２００３年９月１６日 火曜日 午後１２時２３分