Filter
Top Products
4
English
Network Control
■
■■
■ Controling by Computer via Network
1
Start your Web browser.
Compatible browsers are Internet Explorer Ver. 5.0 or later.
Compatible operating systems are Windows 98, 98SE, Me,
2000 and XP.
2
Enter the URL.
Enter the URL for this unit in the address bar of the browser, and
then press the [Enter] key. Enter the IP address specified in the
network setting for this unit. (The URL contains the IP address
that has been set for this unit in the network settings.)
Enter the default value 192.168.0.1.
(Example: “http://192.168.0.1/”)
3
Enter a password (security check).
Enter your user name and password for security checking in
the Network password entry box, and then click [OK].
If you enter an incorrect password, the password entry screen
will reappear asking you to re-enter the password.
(1) You should use separate passwords for different
user levels In accordance with the installation
environment. (See p. 20)
(2) If you choose to save the user name and password that
you enter, the security check will be cleared automatically
the next time you log on. However, passwords that were
entered at some time other than the time when you first
connected may not be stored in some cases.
(3) Up to a total of four computers can be connected
simultaneously to a single digital video recorder.
(However, only one computer can be connected at a
user level of ID2 or ID3.)
(4) If you make more than one error entering the
password or if you click the [Cancel] button in the
password entry screen, an “AUTHENTICATION
ERROR” window will be displayed.
(5) If you click a button on the control panel that you are
not authorized to use during computer control, the
password entry screen will be displayed and you will
be prompted for a security check for the required
user level for that function.
4
Select the display language.
When the security check for the password has been cleared,
the language selection screen will appear. Select a language
and then click [OK]. The operating screen will be displayed in
the selected language and computer control will be enabled.
(1) Select the display language each time you switch to
computer control.
(2) To change the display language, cancel the
connection temporarily and then reconnect.
■
■■
■
Controling by Main Unit
When you click the S button on the computer operating screen, the connection will be canceled and control will
switch to the main unit.
If a Java Script run-time error appears while using
Internet Explorer, change the settings for Internet
Explorer as shown below.
1. Select Internet Options from the Tools menu,
and click the Advanced tab.
2. Make sure that the following check boxes are set
as indicated.
If the port is set to a value other than the default
value of “80”, add a “:” followed by the port number
to the end of the IP address.
Example if the port is set to “81”
http://192.168.0.1:81/
If you do not have a web browser installed on your
computer’s hard disk, you will need to install one.
If the highest-level user connects from a different
computer while four computers are already
connected, the last one of the lowest-level
computers to connect is forcibly disconnected and
the highest-level user has priority.
IMPORTANT
• You cannot connect to the network while a menu screen is being
displayed or when operations associated with playback are
being carried out. Clear the menu display or stop the playback
operation before reconnecting to the network.
• In some cases, you may encounter problems when
connecting to the network via a proxy server. If this
happens, the proxy setting should be canceled.
• If you close the browser without clicking the S button, you will need to wait for at least 1 minute before
reconnecting.
• To forcibly cancel the connection from the main unit, press the [EXIT/OSD] button for two seconds or more. No
connections will be received by the computer for 10 seconds after the connection has been forcibly canceled.
• If communication with the computer is suspended for one minute or more, the connection will be automatically
cancelled and control will switch to the main unit.
L8HBA_US(DSR-3016 NETWORK)(GB only).book 4 ページ ２００３年３月２８日 金曜日 午後６時４４分