Filter
Top Products
D824/D1624 Reference Manual (MIDI Sync Function)
76
MIDI IN
MIDI OUT
MIDI IN
Q
FREQ
GAIN
Q
FREQ
GAIN
Q
FREQ
GAIN
+10
0
-10
-20
-30
-40
-
+10
0
-10
-20
-30
-40
-
+10
0
-10
-20
-30
-40
-
+10
0
-10
-20
-30
-40
-
+10
0
-10
-20
-30
-40
-
+10
0
-10
-20
-30
-40
-
+10
0
-10
-20
-30
-40
-
16
PAN
Q
PAN
ON ON ON ON ON ON ON
SOLO SOLO SOLO SOLO SOLO SOLO SOLO
EQ EDIT
EQ EDIT EQ EDIT
EQ EDIT EQ EDIT
EQ EDIT EQ EDIT
EQ EDIT
SOLO
ON ON
SOLO
STORERECALL
EQ ON
STORERECALL
STORERECALL
SOLO
+1/
/-1
DATA
EXIT
ENTER
MASTER
15
1413
1211
10
9
1-8 ANALOG IN
9-16 ADAT IN
17-20 EFF RTN
AUX1 AUX2
AUX3 AUX4
EFF1 EFF2
ADD.AUX
+10
0
-10
-20
-30
-40
-
ADAT IN
0
-10
-20
-30
-60
-
-40
PANPANPANPANPANPAN
-40
-36
-24
-18
-12
-9
-6
-3
OL
ST BUSS/SOLO
LR
METER
CHANNEL
FADER MODE
KEY MODE
METER
CHANNEL/
CH VIEW
PHASE GROUP
ROUTING/ PAIR/
MMC SEND
CURRENT SCENE STATUS
SETUP
SYSTEM MIDI
EQ/LO
EQ/LO-MID
EQ/HI-MID
EQ/HI-MID
FREQ
GAIN
EFF EDIT
EFF 2EFF 1
EQ LIBRARY
EFF LIBRARY
SELECTED EQ
SCENE MEMORY
REC BUSS
8
7
6
5
4
2020
1 2 3
1919
1818
1717
ANALOG INANALOG IN
EFF RTNEFF RTN
PAGE SELECT
MIDI OUT
MIDI OUT
MIDI IN
MMC or Fostex System Exclusive Message
Computer System
with
MMC/MTC software
Master Recorder
MIDI sound sources
* If correct sync cannot be obtained, re-check the connections/cables and setting of both equipment.
<Note>
In the recorder, the “ABS 0” position is set at “002BAR/1BEAT /00CLK.”
This setting is made in consideration of the time required (it will not sync immediately) for the MIDI sequencer,
etc. to enter into sync. As a result, if the recorder is played back from ABS 0 (LOCATE ABS 0), sync will be
completed by the time it reaches the first bar, and will thus synchronize from head of the tune.
Execution of recording
Various ways of recording can be conducted while synchronizing the recorder and the MIDI
sequencer with the MIDI clock.
MTC sync/MIDI machine control system
The following will explain synchronization by the MTC (MIDI time code) output and the computer
controlling system using MMC (MIDI machine control). In this system, the recorder will be the
master and the computer (with sequence software) will be the slave. The recorder will attach
any desired offset (time difference) against ABS time (absolute time) and output it as MTC in any
desired frame rate. It can also carry out the proper operation upon receiving an MMC and
Fostex System Exclusive Message from outside. In this case, because the recorder can setup a
DEVICE ID number by the SETUP mode “MIDI Device ID Setting” menu, a multiple number of the
unit’s can be separately controlled by changing the DEVICE ID numbers in the transmitted message
from the computer. In regards to the corresponding content for MMC, refer to the “MMC list” on
page “123” and on the Fostex System Exclusive Message, the “Fostex Exclusive List” on page
“124.”
* Set the recorder in the initial state.
* Confirm the program and sampling frequency.