Onkyo DV-SP1000 DVD Player User Manual


 
91
Controlling Other Components—Continued
The DV-SP1000/DV-SP1000E’s remote controller can
learn individual commands from other component’s
remote controllers and then be used to control those
components. Commands can be learnt by the dedicated
leaning buttons—[L1], [L2], [L3], and [L4]—or any but-
ton. Each button can learn up to four commands, one for
each remote controller mode: DVD, Amp, VCR, and TV.
If you’ve entered a control code for a component
(page 86) and certain buttons don’t work as expected,
you can also use this function to program those buttons
individually.
Notes:
The following buttons cannot learn new commands:
[LIGHT] and the [DVD], [AMP], [VCR], and [TV]
MODE buttons.
Learning mode is cancelled automatically if you don’t
press any buttons for 30 seconds.
The DV-SP1000/DV-SP1000E’s remote controller
comes preprogrammed with the commands necessary
for controlling Onkyo DVD players (DVD mode) and
AV receivers (Amp mode). However, you can repro-
gram individual buttons if necessary. The original
commands can be restored by resetting the remote
controller.
To program a button that has already learnt a com-
mand, repeat this procedure. The previously learnt
command will be overwritten.
Like most remote controllers, the DV-SP1000/
DV-SP1000E’s remote controller uses infrared. Com-
mands from remote controllers that don’t use infrared
cannot be learnt.
When the remote controller’s batteries expire, all
learnt commands may be lost and will have to be learnt
all over again, so keep your other remote controllers in
a safe place.
Learning the Commands of Other
Remote Controllers
1
Point the remote controllers at each other,
about 2 to 6 inches (5–15 cm) apart.
2
While holding down the [DVD], [AMP],
[VCR], or [TV] MODE button, press the
[ON] button, and then release both but-
tons.
The MODE button and Tx/Learn indicator light
up.
+
10 0
CLEAR
123
456
789
INPUT
I
+
-
ENTER
S
E
T
U
P
R
E
T
U
R
N
L4
L2L1
V OFFV IN
ASPECT
A
-
B
REPEAT
RSLTNANGLE
SBTTL
AUDIO
L3
T
O
P
M
E
N
U
M
E
N
U
VOL
+
-
V3
TV
INPUTDMS
DVD AMP VCR
DVD
V1 V2
LM RD
ZOOM
CH
L MODE
LEARNING
SEARCH MEMORY DIMMER AMP INPUT
DISPLAY
AUDIO
SEL
ZOOM ON
PICTURE
CONTROL
RANDOM
STEP/SLOW
MUTING
ANGLESUBTITLEAUDIO
ASPECTA
-
BREPEAT
ON STANDBY
TV
TV CH
TV VOL
RC
-
563DV
LAST
MEMORY
RESOLUTION
MODE
AMP INPUT
REC
OPEN
/
CLOSE
VIDEO INPUT VIDEO OFF
ON
MODE
P
O
WE
R
S
L
E
E
P
D
I
M
M
E
R
S
U
R
M
O
D
E
V
I
D
E
O
-
1
V
IDE
O
-
2
T
A
P
E
D
V
D
C
D
C
D
D
V
D
T
U
N
E
R
T
U
N
E
R
P
H
O
N
O
IN
P
U
T
S
E
L
E
C
T
O
R
D
IS
C
T
A
P
E
V
O
L
U
M
E
L
E
V
E
L
C
HS
E
L
P
R
E
S
E
T
M
U
T
I
N
G
TE
S
T
TO
N
E
M
U
L
T
I
-
C
H
INP
U
T
R
E
M
O
T
E
C
O
N
T
R
O
L
LER
G
R
O
U
P
R
C
-3
8
5
S
2–6" (5–15 cm)
RC-563DV
3
On the DV-SP1000/DV-SP1000E’s remote
controller, press the button that you want
to learn the new command.
The Tx/Learn indicator goes off while the button
is being pressed, and comes back on again when
it’s released.
Use the dedicated leaning buttons—[L1], [L2],
[L3], and [L4]—or another button.
4
On the other remote controller, press and
hold the button whose command you want
to learn until the Tx/Learn indicator
flashes.
If the command is learnt successfully, the Tx/
Learn indicator flashes slowly twice, and then the
MODE button and Tx/Learn indicator remain lit.
If the Tx/Learn indicator flashes quickly three
times, the command has not been learnt, in which
case you should try again from step 3.
If the Tx/Learn indicator flashes quickly six times,
the remote controller’s memory is full and no
more commands can be learnt.
5
To learn more new commands, repeat
steps 3 and 4.
When you’ve finished, press the MODE button
that you pressed in step 2.
To use the learnt command, select the relevant
mode, and then press the button.