Filter
Top Products
74
RQT9306
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart
do not solve the problem, consult your dealer for instructions.
No power.
The unit does not turn on pressing [Í].
¾ Insert the AC mains lead securely into a known active
household mains socket. (> 8, 68, 69)
The unit switches to standby mode.
¾ One of the unit’s safety devices is activated. Press [Í/I] on the
main unit to turn the unit on.
The power is turned off automatically.
¾ If you connected this unit to a “HDAVI Control” compatible TV
with an HDMI cable, this unit will be automatically set to
standby mode when the TV is set to standby mode. (> 36)
This unit turns off when the TV input is switched.
¾ If connected with an HDAVI Control 4 compatible TV (VIERA)
with the “Intelligent Auto Standby” setting activated on the TV,
when switching the TV input, the unit will be automatically
turned to standby. For details please read the operating
instructions of the TV.
The display is dim.
¾ Change “FL Display” in the Setup menu. (> 62)
“0:00” is flashing on the unit’s display.
¾ Set the clock. (> 64)
The time recorded on the disc and the available
time shown do not add up.
The displayed time of this unit is different from
the actual recording time or MP3/WMA recording
time.
¾ Times shown may disagree with actual times.
¾ Available recording space on DVD-RW (DVD-Video format) or
+RW increases only when the last recorded title is deleted. It
does not increase if other titles are deleted.
¾ Even if you delete recorded content from the DVD-R, DVD-R
DL, +R or +R DL, there is no increase in disc space.
¾ More disc space than the actual recording time is used after
recording or editing the DVD-R, DVD-R DL, +R or +R DL 200
times or more.
¾ While searching, the elapsed time may not display correctly.
The clock is not correct.
¾ Under adverse reception conditions, etc., the automatic time
correction function may not work. In this case, “Automatic” is
automatically turned to “Off”. If re-setting the Auto Clock Setting
does not work, set the time manually. (> 64)
Compared to the actual recorded time, the
elapsed time displayed is less.
(Only when recording in NTSC)
¾ The displayed recording/play time is converted from the
number of frames at 29.97 frames (equal to 0.999 seconds) to
1 second. There will be a slight difference between the time
displayed and the actual elapsed time (e.g., actual 1 hour
elapsed time may display as approximately 59 minutes
56 seconds). This does not affect the recording.
“U88” is displayed and the disc cannot be
ejected.
¾ The unit is carrying out the recovery process. Do the following
to eject the disc.
1 Press [Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [Í/I] on
the main unit for about 10 seconds. The unit is forcibly
switched to standby.
2 While the unit is off, press and hold [∫] and [CH W] on the
main unit at the same time for about 5 seconds. Remove the
disc.
Television reception worsens after connecting
the unit.
¾ This can occur because the signals are being divided between
the unit and other equipment. It can be solved by using a signal
booster, available from audio-visual suppliers. If it is not solved
by using a signal booster, consult the dealer.
The digital channel information or control panel
does not appear.
¾ Select the length of time (3–10 sec.) in the “On-Screen
Messages” in the Setup menu. (> 62)
¾ The digital channel information will not appear during playback
or recording.
¾ Analogue broadcasts do not support the digital channel
information.
¾ The control panel is only displayed when connected to a TV
supporting “HDAVI Control 2” or later. (> 37)
Teletext and teletext closed caption are not
displayed on the TV screen.
¾ This unit does not support teletext and teletext closed caption.
The grey background does not appear.
¾ Select “On” in “Grey Background” in the Setup menu. (> 62)
Screen size is wrong.
¾ Use the television to change the aspect. If your television does
not have that function, set “Progressive” in the Picture menu to
“Off”. (> 54)
¾ Check the settings for “TV Aspect” in the Setup menu. (> 63)
¾ If you connect an HDMI cable, set “Aspect for 4:3 Video” to
“16:9” in the Setup menu. (> 63)
The recorded title’s screen size is wrong.
¾ Set “Rec for High Speed Copy” to “On”, and set the “Aspect for
Recording” to “4:3”. (> 61)
¾ 16:9 aspect programmes are recorded in 4:3 aspect in the
following cases.
– [-R] [-R]DL] [-RW‹V›] If you recorded or copied using “EP” or “FR
(recordings 5 hours or longer)” recording mode.
– If you recorded or copied to a +R, +R DL or +RW.
– If you recorded with the “Aspect for Recording” set to “4:3” in
the Setup menu.
When you want to record 16:9 programme in the same
aspect, set “Rec for High Speed Copy” to “On”, and set the
“Aspect for Recording” to “16:9”. (> 61)
– By setting “Aspect for Recording” to “Automatic”, there is a
chance that the recording will be made using the wrong
aspect. Match the aspect settings to the broadcast when
recording. (> 61)
It may be possible to adjust the display mode on the TV. Refer to
your television’s operating instructions.
The following do not indicate a problem with this unit:
≥Regular disc rotating sounds.
≥Poor reception due to atmospheric conditions.
≥Image disturbance during search.
≥
Interruptions in reception due to periodic satellite broadcasting breaks.
≥Operations are slow to respond when “Power Save” is set to “On”.
≥Operations do not work due to a poor-quality disc. (Try again
using a Panasonic disc.)
≥
The unit freezes due to one of its safety devices being activated.
(Press and hold [
Í
/I] on the main unit for 10 seconds.)
≥When the unit is turned on or off, there may be an unexpected
sound.
Power
Displays
TV screen and video
DMREX79GN-RQT9306-L_eng.book 74 ページ ２００９年３月２４日 火曜日 午後２時３８分