Filter
Top Products
32
Insignia NS-FSDVDR DVD recorder
www.insignia-products.com
10 Make sure that the information you entered is
correct, then press ENTER. The timer
recording is added to the schedule.
11 To add another timer recording to the
schedule, repeat Step 3 through Step 10.
12 Press TIMER PROG. or SETUP to close the
menu.
13 Press POWER. The icon appears on the
front panel display.
Overlapping timer recordings
If you schedule two timer recordings with
overlapping times, the first recording you
schedule takes priority.
For example, if you schedule program A to
record between 8:00 p.m. and 10:00 p.m., then
schedule program B for the same time, your
recorder records program A instead of
program B.
If you schedule program A to record between
8:00 p.m. and 10:00 p.m., then schedule
program B to record between 9:00 p.m. and
11:00 p.m., your recorder records program A. At
10:00 p.m., your recorder starts recording the
second half of program B.
If you schedule program A to record between
8:00 p.m. and 10:00 p.m., then schedule
program B to record between 10:00 p.m. and
11:00 p.m., your recorder records program A,
then records program B. The first few seconds of
program B may not record because it takes a
few seconds (no more than 30) for your recorder
to switch from one program to another.
Cancelling or correcting a timer program
recording
To cancel or correct a timer recording:
1 Press POWER. The icon disappears from
the front panel display.
2 Press TIMER PROG. The
Timer
Programming
screen opens.
3 To cancel a timer recording, press or to
select the recording you want to cancel, then
press CLEAR.
4 To correct a timer recording, press or to
select the recording you want to correct, then
press ENTER. Press or to select
the item you want to correct, then enter the
correct information.
5 Press TIMER PROG. to close the menu.
6 Press POWER to return to standby mode.
Checking a timer recording in progress
To check a timer recording in progress:
• Press TIMER PROG. The
Timer
Programming
screen opens, and the
recording in progress is highlighted in red.
Stopping a timer recording in progress
To stop a timer recording in progress:
• Press STOP on the front panel. Pressing
STOP on the remote control will not stop
the recording.
Troubleshooting timer recordings
If a timer recording does not record correctly, an
error message appears on the
Timer
Programming
screen next to the recording that
did not work.
Error messages
Tips
• If power fails or your recorder is unplugged for
more than 30 seconds, the clock setting and all
timer programming is lost.
• If a DVD is not in the disc tray, flashes and
your recorder cannot record. In some cases,
appears momentarily near the recording start
time. Insert a recordable DVD.
• When all timer recordings are completed,
flashes. To play or eject the recorded DVD,
press POWER first, then press PLAY or
OPEN/CLOSE .
• During a timer recording or when your recorder
is in standby waiting for a timer recording to
start, you cannot use many of the remote
control or front panel buttons. To make these
buttons available, cancel the timer recording or
timer standby ( disappears).
• To cancel the timer standby mode, press
POWER.
• When the start and the end times are the
same, the length of the recording is set for 24
hours. When your recorder reaches the end of
the recording, it turns itself off.
• When the programmed start and end times are
earlier than the current time, the setting is not
accepted and the entry is deleted from the list
of recordings.
• If the start time is earlier and the end time is
later than the current time, the recording will
start right after you turn off the power.
Note
If more than one minute of a recording is not
recorded, the error message E40 appears next to
the recording on the
Timer Programming
screen.
E1-E22
E37-E39
Recording error other than those listed
in this table
E23-E24 Unrecordable disc
E25-E28 Copy-protected program
E29 DVD is protected.
E30 DVD is full
Timer Programming
2. ---
1. JAN/01 12:57AM 1:57AM CH 8 1H
Date Start End CH Speed
Timer Programming
2. ---
3. ---
4. ---
5. ---
6. ---
7. ---
8. ---
*
JAN/01 12:57AM 1:57AM CH 8 E22
Date Start End CH Speed
08-1031_NS-FSDVDR.fm Page 32 Wednesday, March 12, 2008 2:53 PM