Filter
Top Products
34
ENGLISH
Setting Your Speaker System
for Multichannel Audio Playback
This player contains a built-in decoder for Dolby Digital, DTS
and MPEG audio sources as well as 5.1 channel discrete
audio output. Ideally, a 5.1 channel system contains 6
speakers: 2 front speakers, 2 surround speakers, a center
speaker, and a sub woofer. However, as this is not always the
case, accurately setting the [Speaker Setting] setting to
reflect your speaker setup allows the player’s built-in decoder
to reroute signals to compensate for absent speakers.
Make adjustments in the [Speaker Setting] setting in the
Setup screen Audio 2 menu.
1 Press Enter.
2 Press Enter.
Set to Speaker’s size
3 Move the cursor control joystic up or down to
select the speaker.
4 Move the cursor control joystic left or right to
select Large/Small/Off or On/Off corresponding
to whether the selected speaker is present in
your system or not, respectively.
Set the size of your speakers in the Size screen. The
front left/right [L/R] speakers have a fixed setting of
Large. The center [C], left surround [LS] and right
surround [RS] speakers can each be set to [Large],
[Small] or [Off]. Set a speaker to Large if the main
speaker cone is 120mm (4 3/4”) or more; set to [Small] if
the it’s less than 120mm (4 3/4”). Note that the [LS] and
[RS] speakers cannot be set independently.
The subwoofer (SW) can only be set to On or Off.
The graphic on the right of the screen represents your
speaker setup, with the currently selected speaker’s
name highlighted in blue, and the speakers set to On
highlighted in yellow.
Speaker Setting
SETUP
Exit
ENTER
SelectDistance
L/R
C
LS
RS
SW
Return
Audio1 Audio2
General
Language
Video
Size
— Large
— Large
— Large
— Large
— On
L R
SW
LS RS
Audio Out – 5.1 Channel
Speaker Setting
Gain Setting –
CD Digital Direct – Off
Audio DRC – Off
Move
Exit
Fix
Start
SETUP
Audio1 Audio2 GeneralLanguageVideo
Audio Out – 5.1 Channel
Speaker Setting
Gain Setting –
CD Digital Direct – Off
Audio DRC – Off
Move
Exit
Fix
Start
SETUP
Audio1 Audio2 GeneralLanguageVideo
5 Repeat steps 3 and 4 for each speaker in your
system.
Set to distance from listening position
6 Move the cursor control joystic up to select
[Size] and press cursor control joystic right.
7 Move the cursor control joystic up or down to
select the speaker.
8 Move the cursor control joystic left or right to
select distance from speaker.
Set the distance from your main listening position to
each speaker in the Distance screen. The distance
setting for any speaker that was set to Off in the Size
screen will be grayed out. For the other speakers, enter
the distance to the nearest 0.5 feet (0.1m). You can set
the distance for the [L/R] speakers between 1.0 feet
(0.3m) and 30 feet (9m). Note that you must set the [C]
and [SW] speakers within 6.5 feet (2m) of the [L/R]
setting. The [LS] and [RS] speakers must be set
within -20 feet (-6m) and +6.5 feet (+2m) of the [L/R]
setting.
The graphic on the right of the screen represents your
speaker setup, with the currently selected speaker’s
name highlighted in blue, and the speakers set to [On]
highlighted in yellow.
Note: If your subwoofer is placed beyond the adjustment
range (L/R–6.5 (2)), set to the nearest setting possible.
Surround sound cohesion should not be affected very
much.
Notes
• If you have already completed the Setup Navigator screen
operations, the settings on this page have already been set by
the player.
• If you have not made connections to the AUDIO OUT
(5.1channel) jacks on the rear panel of the player, it is not
necessary to make any changes to this setting.
• To help identify the speakers being selected, the initials of the
speakers in the speaker system representation on the right side
of the screen will appear in blue.
• The menu settings may look different from the one shown above.
Speaker Setting
SETUP
Exit
ENTER
SelectSize
L/R
C
LS
RS
SW
Return
Audio1 Audio2
General
Language
Video
Distance
— 3.0m
— 3.0m
— 3.0m
— 3.0m
— 3.0m
L R
SW
LS RS