Filter
Top Products
64
ENGLISH
15 cm dia.
or more
Condensation
Moisture may form in the operating section of the player if the
player is brought from cool surroundings into a warm room or
if the temperature of the room rises suddenly. When this
happens, the player’s performance will be impaired.
To prevent this, let the player stand in its new surroundings for
about an hour before switching it on, or make sure that the
room temperature rises gradually.
Condensation may also form
during the summer if the
player is exposed to the
breeze from an air
conditioner. In such cases,
change the location of the
player.
Switch POWER to turn off when not using the unit
Depending on the strength of the TV or radio broadcast
signal, having the TV or radio on while
power to the unit is on may result in stripes
on the TV screen or noise. However, this is
not a malfunction of this unit or the TV or
radio. In such a case, switch the power of
the unit to turn off.
Power-cord caution
Handle the power cord by the plug. Do not pull out the plug
by tugging the cord and never touch the power cord when
your hands are wet as this could cause a short circuit or
electric shock. Do not place the unit, a piece of furniture, etc.,
on the power cord, or pinch the cord. Never make a knot in
the cord or tie it with other cords. The power cords should be
routed in such a way that they are not likely to be stepped on.
A damaged power cord can cause a fire or give you an
electrical shock. Check the power cord once in a while. When
you find it damaged, ask your nearest MARANTZ service
center or your dealer for a replacement.
Cleaning the player
To clean the PLAYER, wipe with a soft, dry cloth. For stubborn
dirt, wet a soft cloth with a mild detergent solution made by
diluting one part detergent to 5 or 6 parts water, wring well,
then wipe off the dirt. Also use a dry cloth to wipe the surface
dry. Do not use volatile liquids such as benzene and thinner
which are harmful to the unit.
Notes on using optical cables
• Do not route cords around sharp angles. When storing,
wind the cords so that they have a
diameter of at least 15 cm.
• When connecting, push all the way into
the terminal.
• Do not use cords with a length of over 3
m.
• If moisture or dust has collected on the
plug, wipe it with a soft cloth before
connecting.
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the
trouble may lie in another component. Inspect the other
components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks
listed below, ask your nearest MARANTZ service center or
your dealer to carry out repair work.
The disc table comes back out automatically, shortly after
the disc table is closed.
The disc is dirty or warped.
\ Refer to
‘Disc Care’
(page 63).
The disc is not placed properly on the disc table.
\ Use the disc table guide to align the disc (page 25).
Region number does not conform with this unit.
\ If the region number on the disc does not match the
number on the player, the disc cannot be used (page
67).
There is condensation on the operating section of the
player.
\ Allow time for condensation to evaporate. If player is
near an air conditioning unit, you should move the
player (page 64).
Playback is not possible.
The disc has been loaded upside down.
\ Check that the disc has been loaded with the label
side facing up.
DVD-Audio playback stops.
\ The disc may have bee illegally copied.
mark appears on screen.
The selected function does not operate for that disc.
mark appears on screen.
The operation is prohibited by the player.
Picture playback stops and the operation buttons cannot
be used.
Player malfunctions.
\ Stop disc playback (press STOP 7), then start
playback again.
New settings made in the Setup screen menus while a
disc is playing are ineffective.
Some settings can be changed while a disc is playing, but
are not effective. This is not a malfunction.
\ Make the same setting when the player is stopped.
\ Stop disc playback (press STOP 7), then start
playback again. When playback is resumed, the new
settings should be in effect. Please note that making
settings in the Setup screen menus may cancel the
resume function.
When making changes in the Setup screen menus, is
displayed.
There is a Video CD or CD loaded in the player and the
setting that was changed only applies to DVD
performance.
\ The setting will be effective the next time a DVD is
loaded.