Mitsubishi Electronics HS-HD1100U VCR User Manual


 
15
Your VCR comes with Mitsubishi’s exclusive on-screen operating
system. This system has been developed to simplify the operation of your VCR
with clear, easy-to-understand language and design.
Before your VCR can receive television channels or you can program your VCR to
record, you need to memorize all of the channels you can receive into your VCR
and set the clock. Fortunately, your VCR makes this an easy process with our
menu system.
When using the on-screen menus, use the ADJUST buttons to move the highlight
bar up or down and to change the setting of selected features. Press the ENTER
button to enter a selection or adjustment. Press the CANCEL button to cancel or
clear a setting.
Memorizing Channels Automatically
Using this process, your VCR will automatically memorize all of the television
stations available to you. You can later get rid of unwanted or unused stations.
If your local cable company scrambles some or all stations, and/or requires you
to use a cable box, then your ability to program channels would normally be
limited. The cable box receives all of your channels, then sends only one to
your TV and your VCR, usually on channel 3 or 4.
If your cable box or cable system seems incompatible with your new VCR, call
your cable company. They may be able to provide solutions to your problems.
1 Set the VCR’s input to tuner. To do this, press INPUT on the remote control
until a channel number appears on the screen.
2 Press MENU on the remote control. VCR Main Menu comes up. If First Time
Set-Up is not highlighted, use the ADJUST buttons on the remote to highlight it.
3 Press ENTER. First Time Set-Up menu will appear. Press the ADJUST
buttons to select Memorize channels. Press ENTER.
IMPORTANT
If you are playing back a tape or receiving a video signal from an external input,
Not available will flash and an error message will appear. To correct this, stop
the tape or turn off the menus and switch the VCR’s input to Tuner.
4 You will see the menu for sources connected to the VCR. Using the list below
as a reference, press the ADJUST buttons to select the kind of antenna you
connected.
Cable if you are using any cable combination, including a cable box with an
A/B switch
Indoor/outdoor ant. if you use “rabbit ears” or a roof mounted antenna
After you have selected, press ENTER.
5 An on-screen message will show you that the VCR is memorizing the stations
you can receive. You can cancel the memorization at any time by pressing
CANCEL. After the VCR has memorized all the channels, the screen will
return to the VCR’s picture.
IMPORTANT
Automatic channel memorizing may include vacant channels if there are stray
signals or noise on those channels. If this occurs, you can manually delete the
channels using the procedure in the section Adding an Deleting Channels.
Setting Up Your VCR
213
546
879
0
ADJUST
ADJUST
ENTER
CANCEL
Press to
Enter
Press to
Cancel
Press to
Select
ƒFirst Time Set-Up
≈Set the clock
∆Memorize channels
«Add/delete channels
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to enter
∑ ππADJUST to select
ªVCR Main Menu
¬Program to record
ƒ1394 connection list
√Customize choices
ƒFirst Time Set-Up
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to enter
∑ ππADJUST to select 
A special note to cable box
subscribers
∆Memorize channels
What type of sources are
connected to the VCR?
’Cable
”Indoor/outdoor ant.
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to enter
∑ ππADJUST to select
∆Memorize channels
Now memorizing all the
stations you can receive
Channel 3
Stand by this may take
a few minutes 
To cancel memorization,
press CANCEL