Mitsubishi Electronics HS-HD1100U VCR User Manual


 
47
IMPORTANT
The time gauge and remaining time work by detecting control signals on
recorded tapes. Therefore, they do not function while playing blank tapes.
The remaining time display may not show the correct remaining time if the Tape or
D-VHS Tape function is incorrectly set, if you are using speed search, if you are
using a special length cassette (such as T-10 length), or if you are using a VHS-C
tape with an adapter.
The remaining time display may not work correctly depending on your tape.
Displaying the Current Time
The current time is shown in the front panel display or the TV screen. If you have
not set the clock, or if there has been a power failure of longer than 30 minutes, the
display will show - - : - -. The current time will be displayed when the VCR is off.
To see the current time when the VCR is on:
1 Press DISPLAY twice. The remaining time display will be replaced by the
current time.
2 To turn off the current time, press DISPLAY again.
Customize Choices Menu
In the Customize Choices menu, there are 6 options that you can set. For each of
the 6 options, start with these 2 steps:
1 Press MENU on the remote control. VCR Main Menu appears on your TV.
2 Use the ADJUST buttons on the remote to select Customize choices. Press
ENTER.
IMPORTANT
Customize choices menu consists of two pages. To display the next page,
use the ADJUST buttons to select Go to next page and press ENTER. To go
back to the previous page, use the ADJUST buttons to select Back to
previous page.
Video mute
When you turn Video Mute ON, any blank section of tape or many stations with a
weak signal will be replaced by a blue screen. The sound will also be turned off.
When you would like to try to tune in on a weak station, turn Video Mute OFF.
3 Complete steps 1 and 2 above. Customize choices menu appears. Use the
ADJUST buttons to select Video mute. Press ENTER to set Video Mute to ON
or OFF.
4 Press MENU twice to exit the menus.
IMPORTANT
Video Mute function may not work properly when you playback a section of a
tape where only audio signals are recording.
Advanced Features
VCR
Stop
⁄‡‚‡‡‡‡‡‡‹
Sun 8:30p
0h20m08s
Current time display
PWR.
PM
SP
CH
VCR
L
R
Current time display
(This screen appears during
analog playback only.)
ªVCR Main Menu
¬Program to record
ƒ1394 connection list
√Customize choices
ƒFirst Time Set-Up
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to enter
∑ ππADJUST to select 
√Customize choices
ƒVideo mute ON OFF
ƒAuto power save ON OFF
ƒRF converter ON OFF
ƒAuto PerfecTape ON OFF
Go to next page §
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to change
∑ ππADJUST to select
√Customize choices
ƒVideo mute ON OFF
ƒAuto power save ON OFF
ƒRF converter ON OFF
ƒAuto PerfecTape ON OFF
Go to next page §
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to change
∑ ππADJUST to select
√Customize choices
ƒRentalXpress ON OFF
ƒSearch w/ Picture ON OFF
Back to previous page §
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to change
∑ ππADJUST to select