Mitsubishi Electronics HS-HD1100U VCR User Manual


 
49
The VCR will display the testing status screen. When testing, the VCR records for
one second, then evaluates the recording it made. The entire test takes about 8
seconds. During this time, the PT light on the front panel will flash. If you wish to
cancel the test, press STOP on the remote while the PT light is still flashing.
When the test is done, the VCR will display the rating of your tape for 8 seconds.
On the front panel, the PT light will shine steadily, indicating that the VCR has set
its internal circuitry to make the best possible recording on this tape.
using PerfecTape
®
manually
1 Load a tape that has its erasure prevention tab intact into the VCR.
2 Find a portion of the tape that is OK to record over; this feature will record over
one second of your tape.
3 Press AUDIO/VIDEO on the remote control. Audio and video function menu
appears. Press AUDIO/VIDEO until the PerfecTape function appears.
4 Press ENTER on the remote to begin the test. During this time, the PT light on
the front panel will flash. To cancel the test, press STOP on the remote while
the PT light is still flashing.
When the test is finished, the VCR will display the rating of your tape for 8 seconds.
Turn off the display by pressing STOP on the remote control.
If you wish to erase the settings, eject the tape. The settings will also be erased if
you press TIMER RESET or if the VCR loses power. After the test is finished, the
PerfecTape function will not appear unless the tape is ejected.
RentalXpress
RentalXpress is a feature, when activated, that will automatically rewind the tape to
the beginning, eject and power off the VCR, after it has reached the blank section
of 30 seconds or longer on any rental tape (or any tape with the erasure prevention
tab removed). To activate this feature:
3 Complete steps 1 and 2 on page 47. Customize choices menu appears. Use
the ADJUST buttons to select Go to next page. Press ENTER.
4 Press the ADJUST buttons to select RentalXpress. Press ENTER to select ON
or OFF.
5 Press MENU twice to exit the menus.
IMPORTANT
While the VCR is rewinding to the beginning of the tape, you cannot use
repeat playback, counter zero stop and index search.
Search with Picture
When you set Search w/ Picture setting to ON, it allows you to search (FWD/REW)
your D-VHS recording with picture. If you turn this setting OFF, you will not see
any picture while “searching.” It is preset to ON at the factory.
3 Complete steps 1 and 2 on page 47. Customize choices menu appears.
Press the ADJUST buttons to select Go to next page. Press ENTER.
4 Press the ADJUST buttons to select Search w/ Picture. Press ENTER.
5 Press MENU twice to exit the menus.
IMPORTANT
Even if you set Search w/ Picture to ON, there may be instances where there
will be a frozen picture or no picture while you search. This is due to the
signal that was recorded. This is not a defect of the D-VHS.
Advanced Features
PerfecTape
Band 
High ¤°°°°°°°°°‡‡‡‡‡‡‡› 
Mid. ¤°°°°°°°°°°°‡‡‡‡‡›
Low ¤°°°°°°°°°°°‡‡‡‡‡› 
Test is completed.
VCR
PerfecTape
Use ENTER to start
√Customize choices
ƒRentalXpress ON OFF
ƒSearch w/ Picture ON OFF
Back to previous page §
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to change
∑ ππADJUST to select
√Customize choices
ƒVideo mute ON OFF
ƒAuto power save ON OFF
ƒRF converter ON OFF
ƒAuto PerfecTape ON OFF
Go to next page §
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to change
∑ ππADJUST to select
√Customize choices
ƒRentalXpress ON OFF
ƒSearch w/ Picture ON OFF
Back to previous page §
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to change
∑ ππADJUST to select
√Customize choices
ƒVideo mute ON OFF
ƒAuto power save ON OFF
ƒRF converter ON OFF
ƒAuto PerfecTape ON OFF
Go to next page §
∫πMENU to go back
∂ ππADJUST to select
≤¥≥πENTER to change
∑ ππADJUST to select