Mitsubishi Electronics LT-46153 Flat Panel Television User Manual


  Open as PDF
of 96
 
5. NetCommand IR Control 57
Toperformthisprocedure,youneed:
TheremotecontrolsforboththeTVandthe•
deviceyouwanttocontrol.
AnIRemittercableavailablefromMitsubishi•
.
Note: TosetupanA/Vreceiver,see“SettingUpA/V
ReceiverControl,”page62.
ConnectandpositiontheIRemittersforthe
1.
devicesyouwishtocontrol.See“IREmitterPlace-
ment”ontheoppositepage.
Setthe
2.
TV’sremotecontrolto
TV
modeandpower
ontheTV.
OpentheNetCommand
3.
Learnscreenasfollows:
Ifworkingfromthe• New Device Foundscreen
afterthedeviceisfirstdetected,highlight
NetCommandandpress
ENTER
toopenthe
Learnscreenforthedevice.
IfperformingNetCommandsetupatanytime•
afterthedevicehasbeenrecognizedthrough
AutoInputSensing:
a. Press
ACTIVITY.
b. Highlightthedesiredinputiconandpress
ENTER
toswitchtothatinput.
c. Press
MENU
,highlightInputs,andhighlight
LearntoopentheInputs > Learnscreen
forthedevice.
Thefirstfunctionhighlightedinthe
4.
Learnscreen
isalwaysPower On.AimtheTV’sremotecontrol
attheTVandpress
ENTER
tobeginlearningforthat
function.
Whenthe
5.
Power On
textstartsflashing,aimthe
device’s
remotecontrolattheTVandholdthe
POWER
keyuntilacheckmarkappearsnexttoPower On.
Ifthetextstopsflashingbeforethecheckmark•
appears,repeatthepreviousstep.
ToremovethekeyfromNetCommandcontrol,•
pressthe
CANCEL
keywhilethekeynameis
highlighted.
Pressthe
6.
 keysontheTV’sremotecontrol
tohighlightotherkeysonthelist.Repeatsteps
4and5foreachadditionalfunctionyouwishto
controlthroughNetCommand.
Note: Devicekeysinthefarrightcolumnwillbeasso-
ciatedwiththeremotecontrol’s
MORE
keywhen
“learned.”Seethetableonpage59.
Ifthedevicehasaseparate
7.
POWER OFF
key,press
 ontheTV’sremotetohighlightPower Off.
Repeattheearlierstepsto“learn”the
POWER OFF
key.
If the device has no
POWER OFF
key, skip this step.
Press
8.
BACK
tofinishNetCommand“learning”forthe
currentdevice.
From the New Device Found screen, highlight
NetCommand and press ENTER to open the Learn
screen.
Initial NetCommand Setup
Inputs > Learn screen
Key names marked with a
check have been “learned.”
Device-specific keys in the
rightmost column can be accessed
with the MORE key after “learning.”
Adding or Removing Device Keys from
NetCommand Control
SwitchtheTVtothedevice.Press
1.
ACTIVITY
,high-
lightthedevice’sicon,andpress
ENTER
.
Openthe
2.
InputsmenuandhighlighttheLearnicon.
Whenthe
3.
Learnscreendisplays:
To add keys: • Continueasdescribedearlier
under“InitialNetCommandSetup”onthis
page.
To delete keys:• Highlightthenameofthekey
youwishtodeleteandpress
CANCEL
onthe
TV‘s remotecontroltoclearthecheckmark.
Downloaded From TV-Manual.com Manuals
 previous next