Mitsubishi Electronics LT-46153 Flat Panel Television User Manual


  Open as PDF
of 96
 
66 6. NetCommand Control of an A/V Receiver
IfusinganoptionalaudiocablebetweentheTVand
4.
A/Vreceiver,connectit.
ConnecttheIRemittercabletotheTVandposition
5.
theIRemitterwhereitcansendsignalstotheA/V
receiver.See“IREmitterPlacement,”page56.
Setup to Control Automatic Audio
and Video Switching via HDMI
Whenthissetupiscomplete,the“learned”A/Vreceiver
inputwillappearintheTV’sActivitymenuasaselect-
ableinput.
PowerontheA/Vreceiver.
1.
Setthe
2.
TV’sremotecontrolto
TV
modeusingthe
sidebutton.
PowerontheTV.
3.
Whenthe
4.
New Device Foundscreendisplays,
selectdevicenameAVRifitisnotrecognizedauto-
matically.
Navigatetothe
5.
Inputs > AVRmenuor,from
withintheNew Device Foundscreen,highlight
NetCommandandpress
ENTER
.
To set up A/V switching over HDMI, choose your
devices from a list. Unlike the device list described for
Case 2, this is a generic list containing more than just
the devices detected in your setup.
Inthe
6.
Inputs > AVRmenu,press tohighlight
thenameoftheA/Vreceiverinputtocontrol.Inthis
example,itistheDVDinput.
Press
7.
ENTER
ontheTV’sremotecontrol.
Whilethetext
8.
DVDisflashing,pressandholdthe
DVD INPUT
keyontheA/V receiver’sremotecontrol.
Whenacheckappearsnextto
9.
DVD,releasethe
DVD INPUT
key.
Ifthetextstopsflashingbeforethecheckmark•
appears,repeatthisstep.
ToerasetheIRcodejust“learned,”press•
CANCEL
whilethenameishighlighted.
Iftherearenomoredevicestosetup,highlight
10.
EXITandpress
ENTER
orcontinuetosetupaddi-
tionalA/Vreceiveraudio/videosources.
Setting Up A/V Receiver Control, continued
NetCommand Control of a Device Con-
nected to an HDMI A/V Receiver
UsethissetuptohaveNetCommandcontroladevice
sendingaudioandvideothroughtheA/Vreceivertothe
TVviaHDMI.
Youmusthavealreadycompletedtheprocedureunder
“SetuptoControlAutomaticAudioandVideoSwitching
viaHDMI”onthispage.Thatprocedureplacesanicon
intheActivitymenuforthedevice(input)connectedto
theA/Vreceiver.
HDMI
Cable
TV
Any Connection
Type
Source
Device
A/V
Receiver
SetupNetCommandcontrolofA/Vreceiveraudio/
1.
videoswitchingviaHDMIasdescribedonthis
page.
Press
2.
BACK
tocloseanyopenmenusandreturnto
normalTVviewing.
Press
3.
ACTIVITY
.
HighlighttheiconfortheA/Vreceiverinputyou
4.
wishtocontrol.
Press
5.
ENTER
toswitchtheTVtotheA/Vreceiver
andtheA/Vreceivertotheinput.
Openthe
6.
Inputs > Learnmenu.
PerformNetCommand“learning”forthecon-
7.
necteddevicebyfollowingthestepsin“Initial
NetCommandSetup,”page57.
Downloaded From TV-Manual.com Manuals
 previous next