Filter
Top Products
39
6 Program to record menu appears. Turn the ADJUST dial to choose the
channel you would like to record. Turn the SHUTTLE ring to the right.
• Select External L1 if you connect an integrated HDTV or an IEEE 1394-
equipped HDTV receiver to the rear panel.
• Select External L2 if you connect an integrated HDTV or an IEEE 1394-
equipped HDTV receiver to the front panel.
7 Day will flash. Turn the ADJUST dial to choose the day on which you want to
record; for example, Monday the 12th.
Your choices are:
• a single day up to one month away.
• every day from Monday through Friday; for example, to tape a soap opera.
To program, turn the ADJUST dial until Monday-Friday appears.
• the same day every week; for example, to tape your favorite weekly sitcom.
To program, turn the ADJUST dial until Every and the desired day of the
week appears.
Turn the SHUTTLE ring to the right once you have made your choice.
8 The hour numbers of the start time will flash. Turn the ADJUST dial to set the
hour when recording is to start. Turn the SHUTTLE ring to the right.
9 The minute numbers of the start time will flash. Turn the ADJUST dial to set
the minutes when recording is to start. Turn the SHUTTLE ring to the right.
10 Set the stop time the same way as the start time, using steps 8 and 9.
11 Turn the ADJUST dial to set the recording speed:
SP = standard play; EP = extended play; AUTO = auto. Auto speed
programming is discussed on page 48. Turn the SHUTTLE ring to the right.
IMPORTANT
If you turn the SHUTTLE ring to the right when you set the timer recording
incompletely, Program is not completed will appear on your screen.
If two programmed recording times overlap, VCR is already programmed for
that time will display on your screen for about 3 seconds, and then the Recap
screen will appear. The program you have just set will flash for 3 seconds
and the start time and the stop time will be shown in red letters. The start
and stop time of the overlapped program will be highlighted in red color. You
will need to erase one of them.
12 The programmed memory will appear on the Recap screen.
13 To program additional recording times, select an empty program line by turning
ADJUST dial. Turn the SHUTTLE ring to the right. The VCR Plus+ system
menu will appear. Continue the programming procedure from step 5.
14 When you are finished with all programming, check the following:
• Leave an integrated HDTV or an IEEE 1394-equipped HDTV receiver turned ON.
• Turn the VCR power OFF and make sure the programmed recording light is lit.
IMPORTANT
While the VCR is recording a digital broadcast, please do not change the
channel on an integrated HDTV or an IEEE 1394-equipped HDTV receiver.
The menu or the program list of an integrated HDTV or an IEEE 1394-
equipped HDTV will be recorded if it is displayed during recording.
If you record a digital broadcast in analog format, the picture quality will not
be as clear as that of the original digital broadcast.
If you record a copy protected digital program, the copy protect data will also
be recorded.
Timer Recording
¬Program to record
ƒChannel External L1
ƒDay Monday 12
ƒStart time 11:00am
ƒStop time --:--
ƒRecord speed AUTO
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.
¬Program to record
ƒChannel External L1
ƒDay Monday 12
ƒStart time 11:30am
ƒStop time 1:30pm
ƒRecord speed SP
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.
Recap screen
¬Program to record
CH DAY ON OFF
10 TH15 9:00p10:30pSP
§ L1 MO12 11:30a 1:30pSP
--- -- --:-- --:-- SP
--- -- --:-- --:-- SP
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.
¬Program to record
ƒChannel External L1
ƒDay --
ƒStart time --:--
ƒStop time --:--
ƒRecord speed AUTO
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.
¬Program to record
ƒChannel External L1
ƒDay Monday 12
ƒStart time --:--
ƒStop time --:--
ƒRecord speed AUTO
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.