Filter
Top Products
62
using PerfecTape
®
automatically
1 Load a blank tape into the VCR.
The VCR will display the testing status screen. When testing, the VCR records for
one second, then evaluates the recording it made. The entire test takes about 8
seconds. During this time, the PT light on the front panel will flash. If you wish to
cancel the test, press STOP on the remote while the PT light is still flashing.
When the test is done, the VCR will display the rating of your tape for 8 seconds.
On the front panel, the PT light will shine steadily, indicating that the VCR has set
its internal circuitry to make the best possible recording on this tape.
If you would like to know whether your VHS tape is suitable for S-ET recording, set
the S-ET record in the S-VHS Set Up menu to AUTO then test the VHS tape. If the
tape is suitable, S-ET record: ON is shown on the screen and the tape will record in
S-ET mode. If it is not suitable for S-ET recording, S-ET record: OFF is shown on
the screen and the tape will record in VHS format.
using PerfecTape
®
manually
1 Load a tape that has its erasure prevention tab intact into the VCR.
2 Find a portion of the tape that is OK to record over; this feature will record over
one second of your tape.
3 Press VIDEO on the remote control. Video function menu appears. Press
VIDEO until the PerfecTape function appears.
4 Turn the SHUTTLE ring to the right on the remote to begin the test. During this
time, the PT light on the front panel will flash. To cancel the test, press STOP
on the remote while the PT light is still flashing.
When the test is finished, the VCR will display the rating of your tape for 8 seconds.
Turn off the display by pressing STOP on the remote control.
If you would like to know whether your VHS tape is suitable for S-ET recording, set
the S-ET record in the S-VHS Set Up menu to AUTO then test the VHS tape. If the
tape is suitable, S-ET record: ON is shown on the screen and the tape will record in
S-ET mode. If it is not suitable for S-ET recording, S-ET record: OFF is shown on
the screen and the tape will record in VHS format.
If you wish to erase the settings, eject the tape. The settings will also be erased if
you press TIMER RESET or if the VCR loses power. After the test is finished, the
PerfecTape function will not appear unless the tape is ejected.
RentalXpress
RentalXpress is a feature, when activated, that will automatically rewind the tape to
the beginning, eject and power off the VCR, after it has reached the blank section
of 30 seconds or longer on any rental tape (or any tape with the erasure prevention
tab removed). To activate this feature:
3 Complete steps 1 and 2 on page 60. Customize choices menu appears. Use
the ADJUST dial to select Go to next page. Turn the SHUTTLE ring to the
right.
4 Turn the ADJUST dial to select RentalXpress. Turn the SHUTTLE ring to the
right to select ON or OFF.
5 Press MENU twice to exit the menus.
IMPORTANT
While the VCR is rewinding to the beginning of the tape, you cannot use
repeat playback, counter zero stop and index search.
Advanced Features
PerfecTape:SP
Band S-ET record: ON
High ¤°°°°°°°°°‡‡‡‡‡‡‡›
Mid ¤°°°°°°°°°°°‡‡‡‡‡›
Low ¤°°°°°°°°°°°‡‡‡‡‡›
Test is completed.
VCR
PerfecTape
Use ENTER to start
√Customize choices
ƒRentalXpress (ON )
ƒSearch w/ Picture(OFF)
Back to previous page §
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER to change.
Press MENU to go back.
√Customize choices
ƒVideo mute (ON )
ƒAuto power save (OFF)
ƒRF converter (OFF)
ƒPerfecTape (AUTO)
Go to next page §
ππππππππππππππππππππππππ
Use ADJUST to select,
and ENTER.
Press MENU to go back.