Filter
Top Products
89
'SCART video'
Since RGB and S-VIDEO signals sometimes use the same connections
on a scart cable, the two signals cannot be transmitted simultaneously.
With these settings, you can decide whether RGB or S-VIDEO signals
are to be transmitted. This setting affects only the scart sockets of the
DVD recorder ( EXT1 TO TV-I/O
N output socket and EXT2
AUX-I/O
M input socket).
Please also observe which signals are available at which scart socket of
the TV or how the scart sockets need to be switched.
If necessary, consult the instruction manual of your TV.
O 'RGB'
Depending on the TV you are using, switching between the
'RGB' and the 'Video(CVBS/FBAS)' signal is done automatically.
If the picture scrolls to the side or colour quality problems
appear on some TVs when the setting is 'RGB', you must
select 'CVBS only'.
O 'S-Video'
Only the S-Video signal will be processed at both scart sockets
( EXT1 TO TV-I/O
N output socket and EXT2
AUX-I/O
M input socket).
In case the scart socket of the TV is not suitable for S-VIDEO
(Y/C) signals, you will only see a black&white picture, although
the recording will be made in colour.
Moreover, only the video (CVBS, FBAS) signal will be used for
recordings via the EXT1 TO TV-I/O
N scart socket.
Please observe that when making recordings from a video
recorder that transmits only video (CVBS/FBAS) signals
through the scart cable, recordings via scart socket EXT2
AUX-I/O
M may be made in black and white.
Therefore, use this setting with caution.
O 'CVBS only'
Only the video (CVBS/FBAS) signal is transmitted, regardless
of the video signals (RGB, Y/C) at the scart sockets. This
setting is selected automatically when no 'RGB' or 'S-VIDEO'
signal is detected at the scart socket.
When selecting the settings 'S-Video'or'CVBS only', the RGB signal
is switched off.
The 'RGB' signal is switched off.
O 'S-video + YPbPr'
Component Video (YUV) and S-Video(Y/C).
GUIDE Plus+
®
menus only available on YUV ouput sockets.
O 'CVBS + YPbPr'
Component Video (YUV) and Video (FBAS/CVBS).
GUIDE Plus+
®
menus only available on YUV ouput sockets.
With all other settings, the signal is switched off at the COMPONENT
VIDEO OUT
R sockets. This will also be displayed as information on
the screen.
Sound settings
You can select the settings in this menu depending on which audio
outputs are used.
If you only use the analog audio output (red and white socket AUDIO
OUT L/R
Q ), select the setting 'Off' in the 'Digital output' menu.
Sound
Digitaloutput All
Analogueoutput Stereo
Nightmode Off
'Digital output'
You can select one of the following settings for devices that are
connected to the COAX OUT
S or OPTICAL OUT U sockets:
O 'All'
Dolby Digital and DTS signals are fed unaltered to the digital
output. MPEG-2 multi-channel signals are converted to PCM
(Pulse Code Modulation).
For receivers/amplifiers with digital multichannel
decoders.
O 'PCM only'
Digital and MPEG-2 multi-channel signals are converted to
PCM (Pulse Code Modulation). For receivers/amplifiers
without digital multichannel decoders.
O 'Off'
Digital output switched off.
For devices with analogue audio input.
'Analogue output'
You can select one of the following settings for devices that are
connected to the analog audio output ( AUDIO OUT L/R
Q ):
O 'Stereo'
For devices without DolbySurround or TruSurround. Use this
setting if the DVD recorder is only connected to a stereo TV.
O 'Surround'
Dolby Digital and MPEG-2 multi-channel are mixed down to a
Dolby Surround-compatible two-channel output signal.
For devices with Dolby Surround / Pro Logic Decoder .
'Night mode'
Night mode optimises the sound for playback at low volume. You are
therefore less likely to disturb your neighbours. This only works with
Dolby Digital audio on DVD video discs.
User preferences /settings II