Filter
Top Products
70
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Various search (continued)
Search may not perform properly at times de-
pending on the recorded condition of the index
signals.
Search may take time, depending on the
recording status of the index signal. Press the STOP
button while searching to end search.
6. To clear the search screen, press the SEARCH button twice.
■ ALARM LIST SEARCH
This unit stores the start time of alarm recording and emer-
gency recording in the alarm list when such recording be-
gins. It is also possible to index search the desired time (or
the closest time) from the list of alarm recording (emer-
gency recording) start times stored in the alarm list.
To clear the alarm list, erase the data in the
<MAIN HDD DATA CLEAR> (<SUB HDD DATA
CLEAR>) screen. Beware that executing it erases
all the data of HDD contained the video data. Alarm
recording then will be stored again from 00001.
Up to 10,000 alarm recording (emergency re-
cording) start times can be stored and displayed.
In the alarm list, items with the ALARM IN termi-
nal on the rear grounded are indicated in white, items
that were detected with motion are indicated in green
and items with the EMERGENCY terminal grounded
are indicated in red.
1. Press the SEARCH button.
• The search screen selected in the “SEARCH TYPE” (
see page 67) appears.
<SEARCH SELECTION>
>>
SEARCH TYPE ALARM LIST
SELECTION CAMERA NUMBER ALL
DATE/TIME - - : :
PLAYBACK DEVICE SUB
SUB
START 02-02-2004 00:00:00
END 04-04-2004 12:30:15
The Alarm list may take time to display completely
when there are many list items or the HDD has been
expanded.
2. (When the desired search screen is not displayed on the
screen • • • )
Change the previous “SEARCH TYPE” setting and display the
“ALARM LIST SEARCH” screen.
To display the emergency recording start time in
the alarm list, set “SELECTION CAMERA NUMBER”
in the <SEARCH SELECTION> screen to “ALL”.
“EMR” indicating emergency recording will appear
in the place of the camera number in the alarm list.
<ALARM LIST SEARCH>
>>
00004 01-01-2004 00:00:04 1
00003 01-01-2004 00:00:03 EMR
00002 01-01-2004 00:00:02 1
00001 01-01-2004 00:00:01 EMR
PUSH SEARCH KEY
1
2
Recorded camera
Camera of alarm input
“Camera of alarm input” displays the camera
number which is input alarm signals, and “record
camera” displays the camera number which started
recording.
When the correspondent cameras for alarm sig-
nals are not set for the recording, the record is
storaged using the camera of the youngest number.
When execute “ALARM LIST SEARCH” while
the “PARTITION” is set, set to “SUB” in “PLAYBACK
DEVICE”.
If motion is detected and the ALARM IN terminal
on the back is grounded at the same time, all of
those start times may not be registered to the alarm
list. In such cases, the smallest numbered camera
is registered to the camera list.
4. Select the desired alarm list number and turn the
SHUTTLE ring clockwise to confirm.
• button/turn JOG dial counterclockwise : Selection moves
to the next number.
• button/turn JOG dial clockwise : Selection moves to the
previous number.
• button : Displays the page with date prior to the date of
the currently opened page.
• button : Displays the page with date newer than the date
of the currently opened page.
• To cancel search, press the SEARCH button twice.
• After performing alarm search, the screen will be in the single
screen display with still-frame playback regardless of whether
setting “ALL” in the “SELECTION CAMERA NUMBER” (
see page 67) or selecting an individual camera number.
The camera number written by the start index
signal of the pre-alarm recording may differ from the
camera number displayed in the alarm list.
When setting “HDD REPEAT REC MAIN” to
“OFF” or “STANDBY”, “HDD REPEAT REC SUB” to
“OFF” and there is an alarm recording (emergency
recording) at the end of the HDD, that recording may
not be stored in the alarm list and that number may
become missing and not displayed.
When an alarm recording (emergency record-
ing) is performed during using display of the
<ALARM LIST SEARCH> screen, exit the <ALARM
LIST SEARCH> screen and display the screen
again. The new item will be added to the list.