Filter
Top Products
75
RQT7394
Reference
Recording/Timer recording/Transferring (dubbing) (Continued) Page
TV Guide On Screen
TM
system
Continued on next page
Cannot transfer (dub) to a DVD-
R disc using the high speed
mode.
≥When recording to the HDD, set “DVD-R High-Speed Recording” to “On” in the SETUP
menu.
62
When transferring (dubbing), it
takes a long time even when
high speed mode is selected.
≥Use a disc that is compatible with high speed recording. Even if the disc is high speed
recording compatible, the maximum speed recording rating may not be possible due to the
condition of the disc.
≥It takes longer than normal to transfer (dub) many titles.
≥You cannot high speed transfer (dub) to DVD-R titles longer than 6 hours when using other
Panasonic DVD recorders that are not compatible with EP (8 hour) mode recording.
—
—
—
An unusually loud sound
coming from the rotating
DVD-R.
≥When recording or high speed transferring (dubbing) to a DVD-R, the sound of the disc
rotating may be louder than normal; however, this is not a problem.
—
The DV automatic recording
function does not work.
≥If images cannot be recorded or if the recording is aborted, check the connections and DV
equipment settings.
≥You cannot start recording until the images from the DV equipment appear on the television.
≥Recording may not be performed as desired if the time codes on the tape in the DV
equipment are not successive.
≥Depending on the equipment, the DV automatic recording may not operate properly.
51, 52
—
—
—
Although initial setup for the
TV Guide On Screen
TM
system
was completed hours ago,
television program list does
not display when [TV GUIDE] is
pressed.
≥Leave the unit turned off for at least 24 hours.
≥Initial setup was done incorrectly. (e.g, The user entered the wrong country, ZIP/postal code
or cable TV box information.) Select “Change system settings” menu and verify the data
entered during initial setup. If the settings are wrong, set up the TV Guide On Screen
TM
system again.
≥Check the connection and set up the TV Guide On Screen
TM
system again.
If you connect a cable TV box
–the output terminal of the cable TV box is connected to this unit’s RF IN or IN3 (L3) terminal
–the IR Blaster is correctly connected and installed
–the cable TV box is turned on
If you do not connect a cable TV box
–the antenna cable is connected to this unit’s RF IN terminal
≥The television program list was temporarily unavailable in your area (Wait another 24 hours
or Re-do setup).
≥The television program list is not available in your area. Set the unit using “Auto Channel
Setting”. Note that you can only manually set timer recording after you set the unit using
“Auto Channel Setting”.
≥Consult your service provider if you are using a cable TV box.
—
29
29
8
8
—
7
—
65
—
“Cable code -INCOMPLETE-”
appears in the TV Guide On
Screen
TM
system setup.
≥The unit cannot find the correct IR code for the cable TV box. Consult your service provider. —
As soon as the unit is turned
on, and when you try to start
timer recording, the TV Guide
On Screen
TM
system setup
begins.
≥Even if you do not want to use the TV Guide On Screen
TM
system, you need to complete the
TV Guide On Screen
TM
system setup (until you have to press [ENTER] after the “Watch TV”
message screen is displayed). It will not be displayed after this point.
12
Some or all of the channels
display “No Listing”
≥For a newly installed unit, the TV Guide On Screen
TM
system may not have been given
enough time to download the initial data. This procedure can only occur when the unit is in
standby mode for a period of 24 hours. (During this time, do not turn on the unit as the
download will be interrupted.) Once the procedure takes place the phrase “No Listing” will be
replaced with program information.
≥The channel(s) in question was (were) recently turned “ON” (in the CHANNEL EDITOR
screen) however TV Guide On Screen
TM
system has yet to receive channel data for this
channel. Leave the unit in standby mode.
≥Immediately after beginning use there are several days of blank listings. You can display the
television program list for up to the next 8 days forward without any blank listings by
downloading program lists continuously over several days.
≥The unit was left turned on for an extended period of time and the TV Guide On Screen
TM
system was unable to receive television program list data. Press [Í DVD POWER] to set the
unit in standby mode when not in use.
≥During the data download the station from which data is downloaded had an unscheduled
power outage.
≥If using an off-air antenna, marginally poor reception can cause some of the data to be
missed.
≥If using a cable TV box, it was accidentally turned off. In installations using a cable TV box,
the box must be left on continuously.
—
—
—
—
—
—
—
7394en.book 75 ページ ２００４年７月２０日 火曜日 午後７時２６分